Worldrigs ID: WR153

Model : 3000-CF Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing / Gefco Holemaster 3000-CF Drill Rig
Factory Rated Capacity: 3,700 ft. depth using 3-1/2” drill pipe.
Mast: Cold drawn street tubing, elec. Welded, 3-sect. with 3-way taper on top sect.
Hydraulically raised & lowered. Wired for elec. Lights. Equipped w/retracting
channel swivel guides for reverse circulation swivel. Equipped with ladder,
climber’s safety device.
 

Hgt. 72” Telescoping, Width 86” center to center of mast legs, Depth 48” center
to center of mast legs, Capacity total gross 133,000 lbs. hook load 100,000 lbs.
Racking board capacity 3,000 ft. of 3-1/2” drill pipe, may be mounted to pull 30' ft.
or 40' ft. joints, Crown block….. 6 trip line sheaves, 6 kelly line sheaves & single
sand line sheaf.

Draw works: Drum barrel dia. & length (Trip drum 10” x 13”) (Kelly drum 8” x 17”) maximum single
line pull first wrap (Trip drum 16,600 lbs. w/6 line block) (Kelly drum 16,600 lbs. 3/4” x 525’)
Line dia. & capacity (Trip drum 3/4” x 525’ ft) (Kelly drum 16,600 lbs. 3/4” x 525’ ft) Brakes,
mechanical lugh-leverage type, double self-energized & equalized (Trip drum 27” x 7”)
(Kelly drum 24” x 7”). Auxiliary brake: 15” double rotor parkers none Parkersburg. Catheads, 2,
mounted each end of Kelly drum shaft. One special air actuated for spinning or breakout, mounted
on driller”s side. One foster automatic cathead mounted on opposite side.
 

Rotary Table: Fully enclosed, oil bath type. Spiral bevel gears, ground & lapped in matched sets.
Opening 18” through table for setting casing. Hinges up to allow setting casing up to 34” O.D.
Rotary table, drum & sand reel, 5 forward & 1 reverse.
Air Compressors: for control air….1 or 2 Wabco model 2 AVC mounted on compound case.
For developing wells, ect….model 253-S2 or 50 SDS or equivalent may be installed
on the gooseneck.
 

Engines: 2, each providing 100 continuous BHP, through 17-1/2" fluid couplings,
GM diesel 4031-C is standard; other makes with suitable specs. may be installed.
Compound Case: Engines may be compounded or used singly. Oil spray bath, three shaft, w/jaw clutch.

Transmission: 5 speeds forward….7.20:1, 3.90: 1:2, 12:1:1, 18:1:1, 00:1. 1 speed reverse….7.09:1.
Clutches: Hoisting drum….2 Fawick 18CB500 air clutches; 18”. Kelly drum…. 2 Fawick 21.5E475 air
clutches. 21-1/2”. Rotary table….twin disc CL-211 air actuated clutch. Master clutch….lipe-roll
way 14”; 2 plate. Engines: twin disc 11”; 2 plate. Air Compressor….twin disc 11”; 3-plate.
Controls: Located on side at left of drawworks. Air valve control panel; remote transmission
shifter; throttle; trip & Kelly brakes; hydraulic control & pressure gauge; instrument
panel for engines; weight indicator & driller’s platform.
 

Other Units Cost Extra or Included as a Rig Package:
- Main Generator-60KW, 54KW prime, 2002 Caterpillar model XQ60P2
- Blowout prevention & well control equipment - 8” 3M Regan “Torus” angular preventer 2”
5M Demco valve on side outlet spool, 2” 5M manifold w/adjustable chokes.
- Doghouse/Toolhouse-8” x 36” trailer mounted.
- Substructure-4” w/pony sub.
- Back-up Mud Pump-Ideco 6” x 12” with 325 HP diesel engine.
- (135) Drill Pipe = 4,500’ ft (4-1/2").
- Drill Collars-150’ ft x 6”.
- Survey Machine-Mathey Wireline unit 12,000’ ft with .092 line.
 

Located : Africa

Worldrigs ID: WR684
Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Moyno water pump
Cummins Diesel deck engine
Detroit 671 T Diesel Engine in truck
140 lb. Safety Hammer
100 ft 6-5/8” augers
rods, bits, etc. included

Location : USA

Worldrigs ID: WR789
Model : TLS Drill Rig
Manufacturer : PortaDrill
Year : 1978
Condition : Used

Description :

1978 PortaDrill TLS Drill Rig
Rebuilt - Volvo Diesel Deck Engine - rated 500 HP
500 ft. of 3-1/2" inch Drill Pipe included
Pipe Rack
Top head was rebuilt in summer 2018
New Water Injection Pump installed in summer 2018
Mounted on a Truck
Cummins diesel engine

Location : USA

Worldrigs ID: WR649
Model : KAT.ST.250 Drill Rig
Manufacturer : Generic
Year : 2018
Condition : New

Description :

2018 KAT.ST.250 Fully Hydraulic Drill Rig
Engine: Aircooled  MAGIRUS  DEUTZ   125  HP
Rotary head torque: 3,800 Nm
Rotary head stroke : 3.35 m.
Pull back capacity: 11.5 ton
Pull down capacity: 7 ton.
Max. drill pipe length : 3 m
Foam pump 50 Bar options

This particular drill rig can be operated in three different modes (Using optional equipment)
1) Water drilling
2) Compressed air and foamdrilling
3) Compressed air and hammer drilling

Location : Eastern Europe Region

Worldrigs ID: WR855
Description :

1976 Ingersoll-Rand Cyclone TH60 Drill Rig
Leroi 450 CFM / 250 PSI Air Compressor
Hydraulics and Compressor are PTO powered by truck engine
Mounted on International Paystar truck
8V92 Detroit diesel engine with Jake brake
13-speed Eaton fuller transmission
Front tires 4 years old, Rear older but good tread
(Drive tires in pic are not current)
Air over hydraulic for controls
980 ft sand line new 2 years ago
Main winch cable needs replacing soon (unknown age)
Pull back cables new 3 yrs ago
New swivel bearings and seals in Feb this year
New water pump 3 yrs ago
Regularly service
Hours unknown
Some gauges work some dont
Has some oil leaks in hydro system
Its ready to drill

Location : USA

Worldrigs ID: WR603
Model : 3000 Drill Rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 3000 Trailer Mounted Drill Rig
Set up for RC
Brewster 18" removable Table
Single draw works
7 Part Main block
2 Cat heads
New Hydraulic pump system
New Hydraulic winch for Tail out
International DT466 Diesel engine
Trailer mounted
6 Leveling jacks
Hydraulic tower ram
Dog House-- Optional at extra cost
The rig is 12’ 6” tall when connected to a day cab tractor. The width is 8’

Location : USA

Worldrigs ID: WR352

Model: 45C Drill Rig
Manufacturer: CME Drill
Year: 2002
Condition: Used

Description :

2002 CME 45C Drill Rig
With 9278 hours
Auto hammer
Wireline winch
Deutz 3 cylinder diesel engine
Mounted on a 2002 Ford F550 Truck 4x4
148,413 miles

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR836
Description :

1977 Ingersoll-Rand TH60 Drill Rig
IR 600 cfm / 250 psi air compressor
Mission style magnum mud pump
Pipe Rack
Mounted on a 1977 International Paystar Truck
Detroit 8V71 Diesel Engine (Rebuilt in 2013-2014)
Hydraulic Leveling Jacks
Drill Pipe is not included (cost extra)

Location : USA

Worldrigs ID: WR646
Model : 670 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1972
Condition : Used

Description :

1972 Chicago Pneumatic 670 Drill Rig
International 510 gas engine (barley runs)
5-speed transmission
CAT 3406 diesel engine
GHH 750 cfm / 300 psi air compressor
Jib & carousel
Includes as a package:
8” hammer w/ 8” bit
6” hammer w/ 6-¼” bit
Jib & carousel
800 ft of 4 inches x 20 ft drill pipe

Location : USA

Worldrigs ID: WR780
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
mounted on an IH Truck
All original parts
Head need work
Good Parts Machine

Location : USA

Worldrigs ID: WR852
Description :

1989 Schramm T-660 Drill Rig
Detroit 8V92 Diesel Deck Engine (less than 4000 hours since
complete rebuild with preheater)
GHH 900 cfm / 350 psi Air Compressor (Rebuilt, less than 500 hours,
with clutch)
Jib-Boom
Bean water injection pump
360 ft of drill pipe (20ft x 4-1/2"), table bushings & basic tooling included
7 Rod Carousel Lazy Susan
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a GMC White Brigadier Truck (60k+ miles on gauge)
Cat 3208 (Rebuilt transmission less than 2000 miles ago)
Very good tires
Note: Replaced upper chains when the motor were rebuilt about 3500 hours ago

Current repairs needed we are aware of:
Truck CAT 3208 engine starts very hard but once it starts then it runs fine and
runs good (Rebuild time approaching soon)
Traverse cylinders leak small amounts of oil
Deck deck engine leaks small amounts of oil
Compressor clutch work manually only

Location : USA

Worldrigs ID: WR411

 

Description:

 

 

 

Worldrigs ID: WR765
Model : 1250 Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing 1250 Drill Rig
Mounted on a Ford Truck
Diesel Engine
5x6 Duplex Mud Pump
Table Drive & Break out wrench
Pipe Rack
300 ft of drill pipe

Location : USA

Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR687
Model : B57 Drill Rig
Manufacturer : Mobile
Year : 1988
Condition : Used

Description :

1988 Mobile B57 Drill Rig
306 cylinder gas engine on deck
3L6 Moyno water pump
Auto hammer, recently calibrated (8/16/2018)
Cathead
Mounted on Gemco articulated carrier powered by Detroit Diesel
It just finished a job in July that lasted about 4 weeks with borings
as deep as 100 feet.
They went over the whole thing, installed new carburetor.

Location : USA

Worldrigs ID: WR352

Model: 45C Drill Rig
Manufacturer: CME Drill
Year: 2002
Condition: Used

Description :

2002 CME 45C Drill Rig
With 9278 hours
Auto hammer
Wireline winch
Deutz 3 cylinder diesel engine
Mounted on a 2002 Ford F550 Truck 4x4
148,413 miles

Location : USA

Worldrigs ID: WR578

Model : DR12/36 Drill Rig
Manufacturer : Foremost Barber
Year : 1995
Condition : Used

Description

1995 Foremost Barber DR12/36 drill rig
Sullair 1150 CFM / 350 PSI Air Compressor
Cummins KTA19 Diesel Deck Engine (2 Stage) - 600 HP @ 2100 RPM
Cat 12 GPM triplex water injection pump @ 600 psi
Lower Rotary Casing Drive
Opening : 24.7" (627mm)
Stroke : 12' (3 660mm)
Rotation : 0-22rpm
Torque(max) : 1,000,000 lb.in., (113 000Nm)
Hoist Capacity : 72,000 lbs (33,000kg)
combined with top drive  108,000 lb (49,000kg)
Pull Down Capacity : 33,000 lbs (15,000kg)

Top Drive
Stroke : 26' (7 930mm)
Rotation : 0-90 rpm
Torque(max) : 84,000 lbs. in., (9 470Nm)
Hoist Capacity : 37,400 lb.in (17,000kg)
Pull Down Capacity : 16,500lb (7,500kg)
Hoist Speed : 0-64 ft./min (0-20m/min)
Jib Boom / Winch: Pullmaster M5 winch with 120' ft of
wire rope single line pull of 6,000 lbs

Mounted on a Volvo GMC truck
Cummins L10 Diesel Engine at 300 HP @ 2100 RPM
Transmission : Fuller RTX11708LL
10" inch drill pipes (100 meters availiable for an extra cost)

Accessories at an Extra Cost: 
Drill Pipe (4 1/2" x 30' ft) 15 unitsDrill Pipe (30' ft) 18 unitsHammer Bits
(15"-17")Hammer Bit (12")Spindle Adapter (4 1/2" * 1)  and (10" * 1)
Casing Jaw 10" one set , 16" one set and 24" one setDischarge Swivel * 1

Location : South Korea, Asia Region

Worldrigs ID: WR544

Model: CME-92 Drill Rig
Manufacturer: CME Drill
Condition: Used

Description :

CME-92 Drill Rig
Deck Engine
Mounted on a 5 Ton Chassis Truck
Ford Gas Engine (Model CSG-649P-6006-E)
511,600 km 
3 Hydraulic Leveling Jacks
No Tooling or Hammer will be provided with the unit

Location : USA

Worldrigs ID: WR790
Model : 500 Drill Rig
Manufacturer : Midway
Year : 1969
Condition : Used

Description :

1969 Midway 500 Drill Rig
Mounted on 1969 Peterbilt Truck
Leroi 100S Air Compressor
Gardner-Denver 5x6 Duplex Piston Mud Pump
New Rear Jacks
Recent Cummins Swap
Transfer case rebuilt in summer 2018
Comes with 200 ft. of 2-7/8” drill pipe
Currently working
Ready to drill

Location : USA

Worldrigs ID: WR781
Model : DSI QuikDrill Rig
Manufacturer : Speedstar
Condition : Used

Description :

Speedstar DSI QuikDrill
Failing FM-3 Mud Pump
Has Air Compressor (Not Working)
Mounted on 2001 International 4900 Truck
Powered by 7.6 L 466 CID L6 International DT466 Diesel Engine

Location : USA

Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR604
Model : T450 Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T-450 Drill Rig
Holte Casing Hammer
Diesel Deck Engine
Air Compressor is low pressure
Mounted on a Truck
Diesel Engine
53,784 Miles on gauge

Could be sold as a package:
Drill Pipe 600’ ft of 4-1/2” & 185’ ft of 3-1/2”
Tulsa Rig Iron Mud shaker
Pipe Truck
assorted bit and reamers

Location : USA

Worldrigs ID: WR837
Description :

Geoprobe 8150LS Crawler Drill Rig
Geoprobe 50DT Track Base Platform
Geoprobe GV5 Sonic Head Long Stroke
Geoprobe Designed Rod Handling
System Head Feed Stroke: 157"
50K Dynamic Force
Remote Diagnostics
Adjustable Swing-arm Control Panel
Automatic Drop Hammer 140 lb
Winch Kit: 2,500 lb

Safety Cage
Triplex High Pressure Water Pump
Air Compressor Kit, C6.6 with BA-922
Drop Rack System with Rod Rack
Drill Mast Side-Shift
Head Centerline Side-Shift
Fits in 40 ft Shipping Container for Exporting
10-ft Tooling Compatible
Rock Coring Compatible
14" in Double Wrench Breakout

Dual Winch System
Front and Rear Outriggers (Four Point Stabilization)
Sonic tooling inventory with rig: (extra cost or included as a package)
Two tooling indexing racks with rollers
230 ft of 4 tooling
230 ft of 6” tooling
100 ft of 8” tooling
One Actuator core for rod handler
One SDT-60 Weighted Wire Line Core Barrel
Several bits and adapters
(Cost Extra or included as a package for all listed together)
2010 Freightliner model Cascadia Truck with Diesel Engine (492,560 miles)
Trailer for the hauling the drill, pipe, and tooling (as is in the pictures)
1210 Hours on Engine, 210 Hours on Sonic Head at time of listing.

Location : USA

Worldrigs ID: WR772
Model : 14W Drill Rig
Manufacturer : Gardner Denver
Year : 1971
Condition : Used

Description :

1971 Gardner Denver 14W Drill Rig
Rig Engine: 350 cummings 855 Diesel
Has 8500 hours
10” rotary table
5 X 6 gear driven Gardner Denver mud pump
600 cfm / 250 psi GD air compressor with blower
600ft of 4-1/2” X 15ft drill pipe and break out tooling / 24ft Kelly
In good working order, ready to drill today
Arc welder is not included.
Package Includes 2 Support Trucks

Location : USA

Worldrigs ID: WR600
Model : T450BH Crawler Drill Rig
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T450BH Crawler Drill Rig
CAT 3406C diesel engine (newly rebuilt - couple hundred hours on engine)
Sullair 900 cfm / 350 psi Air Compressor (3000 hours since rebuilt)
Hours: 8000 or a little less.
Dust Collector
5-Rod Carousel
Everything is in good working order.
100 ft of Schramm Drill Rods (25 ft. length x 4-1/2 in.) & QL60 6-1/4" bits

Location : USA

Worldrigs ID: WR316

Model : DRC-10-A Crawler Drill Rig
Manufacturer : Nordic Drill
Year : 2015
Condition : New

Description :

2015 Nordic Drill DRC-10-A Crawler Drill Rig

All in One Drilling Rig with Dual Rotary, Crawler Mounted Carrier,
12" Max Openings & Slide Angle Mast with Advantages
Compared to a Conventional Air Rotary Drill:

Angle Slide Package: Allows Drilling Applications for Mining,
RC (Reverse Circulation) Exploration, Anchors, Pilling, Geotechnical,
Soil Samples, Etc.

Crawler: Light Weight & Small means less damage to the drilling sites,
allows set up on difficult terrains & access sites, and less preparation
for set up and break down.

Dual Rotary: Allows Accuracy & Performance in Tough Overburden Conditions,
Good Sampling & Screen Intallations, Facilitates The Extraction of Casing,
Easy to Operate & Cleaninesss on Sites.

Safety: Offers Safe Drilling Methods, Provided of an Anti-Rotation System.

Top Drive:
- Stroke: 16' ft
- Hoist: 31,000 lbs
- Hoist Speed: 53 ft/min
- Pull Down: 23,500 lbs
- Pull Down Speed: 71 ft/min
- Torque: 6,000 ft x lbs
- Rotation Speed: 0-90 RPM

Lower Drive:
- Stroke: 10' ft
- Hoist: 35,000 lbs
- Hoist Speed: 47 ft/min
- Pull Down: 26,500
- Pull Down Speed: 63 ft/min
- Torque: 21500 ft x lbs
- Rotation Speed: 0-9 RPM
- Maximum Opening: 12"

Engine: CAT C 6.6 Diesel @ 210 hp
Sliding Mast Stroke: 36"
Welding machine: Hydraulic 225 AMP
Water Pump: Quad Bean 18 GPM
Hydrofrac Pump: 26 GPM @ 1800 psi / 13 GPM @ 2900 psi
Service Winch: 2,000 lbs
Front Winch: M12 12,000 lbs
Pipe Tub: 40 Pipes - 3-1/2"
Safety: Anti-Rotation Top Drive
Maxumum Speed: 3,1 MPH
Weight: approx. 37,400 lbs

Manufactured in Canada

Worldrigs ID: WR857
Description :

1973 Gardner Denver 14W Drill Rig
Mounted on a CCC (Crane Carrier Company) Truck
390 ft of Drill Pipe included
Mud Pit & Tee
1000 cfm / 250 psi Air Compressor  
Gardner Denver 5x6 Mud Pump
Bean Water Injection Pump
Cummins 350 Diesel Engine
Foller 13 Speed Transmission
Hour meter reads 1978 Hours
Mileage reads 18,687 Miles
Newer Front tires

Location : USA

Worldrigs ID: WR315

Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New

Description :

Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires

Location : USA

Worldrigs ID: WR798
Model : CM-780D Blasthole
Manufacturer : Ingersoll-Rand
Year : 2003
Condition : Used

Description :

2003 Ingersoll-Rand CM-780D Blasthole Drill Rig
Crawler Mounted
Caterpillar Diesel Engine
S/N: G78255EL
IR HR2 865 CFM / 350 PSI Air Compressor
Water injection
Hammer Lubricator
Thread Greaser
Enclosed Cab
A/C & Heater
Rod Changer
13-1/2" Track Shoes
Set up for (3-1/2”O.D. x 13.1ft) Drill Pipe 21/2Z thread
Meter Reads 15,940 Hours

Location : USA

Worldrigs ID: WR773
Model : T64HB Drill Rig - Retrofitted
Manufacturer : Schramm
Year : 1978
Condition : Used

Description :

1978 Schramm T64HB Drill Rig - Retrofitted in year 2000
Detroit 8V92 diesel deck engine
T660 Derrick replaced the T64HB Derrick
Sullair 900 cfm / 350 psi Air Compressor
Carousel
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a 1986 Ford L8000 Truck
CAT 3208 diesel engine
13 speed Eaton fuller transmission

Location : USA

Worldrigs ID: WR762
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 Range III Drill Rig & Pipe Handling System
Hours 27,319+
Heavy‐duty Derrick and Top head Drive pullback of 120,000 lb
51 ft. 7" in. clearance - plenty of room for 30 ft. drill pipe
8,000 ft‐lb. Spur gear power head
Cummins QSK‐19C Diesel Deck Engine - rated 755‐hp
IR HR2.5 1,250 cfm / 350 psi Air Compressor over/under Air End
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar C13 Diesel Engine - rated 380 HP
Mileage  32,531+
Note: Package Includes:
2014 Foremost Pipe Handler 4000 Series (hydraulic pipe handling system -
hands free) on a 2 axle Trailer
The engine, compressor and hydraulic pumps are mounted on a floating
power‐pack

Location : USA

Worldrigs ID: WR103

1995 Foremost Barber DR12/36 drill rig
Sullair 1150 CFM / 350 PSI Air Compressor

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR763
Model : M8A Drill Rig - Table Drive
Manufacturer : Davey
Year : 1965
Condition : Used

Description :

1965 Davey M8A Drill Rig
Davey Piston Air Compressor
Serial Number: 381
300 CFM / 100 PSI Piston Air Compressor
Detroit 6-cylinder Diesel Engine Deck Engine
20 ft. kelly bar - Table Driven
Set up to run (15 ft. x 4 in.) OD drill pipes
Comes with 240 ft. of drill pipe in Rod box
DTH Hammer Oiler Working Condition
Mounted on a 1995 Ford Truck
Diesel Engine
12R22.5 tires
Mileage 99,202 miles
Dimensions: 34ft x 8ft 5" x 13ft
Note: hasnt drilled since late 2017

Location : USA

Worldrigs ID: WR674
Model : T670W Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1979
Condition : Used

Description :

979 Chicago Pneumatic T-670W Drill Rig
Loader Lock Carousel
Breakout Wrench
20 ft x 4-1/4” of used Drill Pipe
CAT 343 V6 Diesel Deck Engine (Turbo)
425 cfm / 250 psi Air Compressor
Oil Lube Pump
Bean Water Injection Pump - 1267611
Hydraulic Winch Line
3 Outriggers
Hydraulic Pull Down & Pull Back
Autofeed
18” Table Opening
320 ft of Pipe Trough
7 Rod Carousel
Auto Rod Loader
Complete Part & Service / Repair Manual Hydraulic Jib
Hydraulic Adjustable Jib Arm
Setup for AIR and MUD Drilling
Mounted on G.M.C. 7500 Series
Detroit 6V-53 Diesel Engine

Location : USA

Worldrigs ID: WR779
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : As-Is

Description :

Chicago Pneumatic T650 Drill Rig
Mounted on a 6 x 6 Oshkosh Truck
Modified drill rig
Direct drive off of the truck engine
900 cfm / 350 psi air compressor

Location : USA

Worldrigs ID: WR178

Model : 1250 Drill Rig
Manufacturer : Failing
Condition : As-Is

Description :

(1) Failing 1250 Drill Rig (being sold for parts)
No Rotary Table
No Mud Pump
No Transfer Case
No Kelly
No Chains
(Basically If You Need A Tower Or Something)
Mounted on a International Truck
Diesel Engine
(1) International 1500 Galloon Water Truck
10 Wheel
Water tank built to bed -O- to haul from pipe beside tank

Location : USA

Worldrigs ID: WR874
Description :

Gardener Denver 15W Drill Rig
Rebuilt and Painted
Truck engine has been rebuilt
Mud pump has also been rebuilt
10” Gardner Denver Retractable table
58ft Mast
Racking board
Bailing drum
new 2” little giant swivel
new 26ft Kelly
hydraulic pull down
air clutches
4 hydraulic leveling jacks

Location : USA

Worldrigs ID: WR876
Description :

1988 Ingersoll-Rand ECM 350 Drill
Mounted on crawler metal tracks
It was an operating unit when it was park
Note: Can include a 1997 Ingersoll-Rand 750 Air Compressor with 1100 hours

Location : USA

Worldrigs ID: WR546

Model : D40K Drill Rig
Manufacturer : Driltech
Condition : Used

Description :

Driltech D40K Drill Rig
50,000 lbs of pullback
high torque head
No carousels (removed for large diameter Well drilling)
dual winches 6000k single line
18000K single line hydraulic Denison P7 main pump - replaced early p-5
All pumps where rebuilt or replaced in 2015 including main gearbox rebuild
Replaced / upgraded to Mercedes tier 4 (I) 550hp diesel deck motor
900 CFM / 300 PSI air compressor
has a mud line and a true 3" mud swivel added to it so it's "mud ready"
New in 2015 radiator/engine cooler rated at 450hp Additional hydraulic cooler added
Mounted on 2012KW tier 4 435hp Paccar heavy spec truck
dual steering and full locking rears
Heavy duty engine Brake
Rig needs a few new hydraulic hoses and new paint job
Note: this machine is 100% California CARB compliant

Location : USA
 

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR598
Model : T130XD Drill Rig - Tilt Power Head
Manufacturer : Schramm
Year : 2007
Condition : Used

Description :

2007 Schramm T130XD Drill Rig
Detroit DDC/MTU V12-2000TA DDEC Diesel Deck Engine
18,500 Hours
Top Head: Tilt head - two hydraulic motors. 0-143 RPM with 106,600 in-lb of torque
50' feet (15.25 m) of clear head travel
Range III casing
130,000 lbs of Pullback
Free standing design with 28" table opening
Hydraulic pumps
Proheat engine heater
Hydraulic stabilizers
Mounted on a CCC (Crane Carrier Corp) 10X4X4 Truck
Caterpillar C13 ACERT Diesel Engine
Eaton Fuller 8LL Transmission
Air Lift 3rd axle

Location : USA

Worldrigs ID: WR350

Model No : V-2000NG Drill Rig
Manufacturer : Versa Drill
Model Year : 2004
Condition : Used

Description :

2004 Vera Drill V-2000NG Drill Rig
Mounted On A 2003 Kimble Model C3300 6x6 Carrier Truck
Eaton 10 Speed Transmission
5,000 Hours
Fabco 23,000 Lb Front Axle
Spincer 46,000 Lb Rear Axles With Different Lock Out
3-Stage Jake Brake
250 Gallon Aluminum Fuel Tank
Aluminum Wheels
Aluminum Cab
Aluminum Diamond Plate Fenders
Cat C-16 600hp Diesel Engine
Ingersoll-Rand 1070cfm/350psi Air Compressor
80,000lb Pull Back/34,000lb Pull Down
3-Speed Top Head Drive
18,000 Lb Hydraulic Main Winch With Jib
2,000 Lb Auxiliary Winch With Jib
Automated Pipe Storage And Controlsystem
New Batteries
Good Rubber
All Wheel Drive
500' Of 2 7/8 X 4 1/2" Drill Pipe

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR775
Model : SDC500-29P Drill Rig
Manufacturer : Sonic
Condition : Used

Description :

Sonic SDC500-29P Drill Rig
80k Diedrich head
28ft stroke, 37ft 8" overall, 24k pullback 16k pull down
12k 5/8" x 222ft nonrotating winch
4"-13" nominal clamping break out table
Hydrostatic circuit 4500PSI
pilot control
micro feed
float
high/low feed, 120gal hydraulic tank
Mounted on a 2004 International 7600 6x4 Truck
Cummins ISM 320V upgraded ECM - rated 385hp
A45/1450 ft torque
Eaton Fuller 13 speed transmission
Hendrickson 38k rear axles
11R22.5 tires
FMC bean pump
3L6 Moyno
Head #A0001 Rebuilt 3/22/12, 11/17/16 (upgraded roller bearings)
9/11 complete engine overhaul (95k chasssis)
Completely rebuilt table (all new) 11/17/16
Rebuilt bean pump (FMC w1122BCD) 2/11/19
New main Hydraulic pumps 3/27/17
New cam rollers for head cradle 10/11/17
Odometer 16,188m 2,466Hrs

Location : USA

Worldrigs ID: WR691
Model : 1500 drill rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 1500 drill rig
5x6 mud pump
kelly drive recentlly rebuilt
Mounted on a twin axle carrier
Diesel engine
Note: no air compressor on board

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR407

Worldrigs ID: WR838
Description :

Foremost DR-40 Crawler Drill Rig
700 hours
Cummins Diesel Engine
24" Tracks
1250 CFM / 350 PSI Air Compressor
Water Injection Pump
Winch for rods
Telescopic boom
Mounted on a Tracks carrier

Location : USA

Worldrigs ID: WR649
Model : KAT.ST.250 Drill Rig
Manufacturer : Generic
Year : 2018
Condition : New

Description :

2018 KAT.ST.250 Fully Hydraulic Drill Rig
Engine: Aircooled  MAGIRUS  DEUTZ   125  HP
Rotary head torque: 3,800 Nm
Rotary head stroke : 3.35 m.
Pull back capacity: 11.5 ton
Pull down capacity: 7 ton.
Max. drill pipe length : 3 m
Foam pump 50 Bar options

This particular drill rig can be operated in three different modes (Using optional equipment)
1) Water drilling
2) Compressed air and foamdrilling
3) Compressed air and hammer drilling

Location : Eastern Europe Region

Worldrigs ID: WR701
Model : D25KW Drill Rig
Manufacturer : Driltech
Year : 1997
Condition : Used

Description :

1997 Driltech D25KW Drill Rig
Sullair 900X350 Air Compressor
W/A CAT C15 Deck Engine (Engine has less than 1000 hours since rebuild)
Mounted a Ford LNT 8000 W/A 300 HP Cummins Engine
8LL Transmission
18,000 Front Axle, 46,000 Rear Axle
Pipe Rack Holds 15 PCS.
Rotary Head 89 RPM, 72,600 LBS. Torque
JIB Boom, Hydraulic extend W/180 degree Hydraulic Swing
Winch, Hydraulic 7,500 LB. Capacity
Drill Table, 20" Opening with Hydraulic Adjustment
Breakout Wrench, 48" jaw type
Remote Control Station
Water Injection, 20 GPM with foam pump
Airline Lubricator
Operators Platform
Fine Feed & Torque Controls
Night Lights
Slip Bushings
With 420 feet OF 4-1/2" X 20 FT. Drill Pipe & Tooling.
It has Good Tires and Runs Strong.