Worldrigs ID: WR674
Model : T670W Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1979
Condition : Used

Description :

979 Chicago Pneumatic T-670W Drill Rig
Loader Lock Carousel
Breakout Wrench
20 ft x 4-1/4” of used Drill Pipe
CAT 343 V6 Diesel Deck Engine (Turbo)
425 cfm / 250 psi Air Compressor
Oil Lube Pump
Bean Water Injection Pump - 1267611
Hydraulic Winch Line
3 Outriggers
Hydraulic Pull Down & Pull Back
Autofeed
18” Table Opening
320 ft of Pipe Trough
7 Rod Carousel
Auto Rod Loader
Complete Part & Service / Repair Manual Hydraulic Jib
Hydraulic Adjustable Jib Arm
Setup for AIR and MUD Drilling
Mounted on G.M.C. 7500 Series
Detroit 6V-53 Diesel Engine

Location : USA

Worldrigs ID: WR854
Description :

Gus Pech 1000R Drill Rig
Set up for Mud Rotary & Auger
Mounted to a 1989 International 1900 Truck
5 speed transmission 2 speed rear
1936+ hours on rig
3 x 4 centrifugal mud pump
3" plumbing to side swivel
450 ft of (4.5″ x 3-2-7/8") drill pipe & holds 225 ft on board the pipe rack
Mud pan attaches to back of rig for transport
Comes with CAT head and auger attachment
3 winches
Jib winch Pullmaster winch 8500 lbs with rapid reverse
wire line for test sampling
2000 lbs sandline
Developmental air compressor
Tophead slides off pole to set pipe
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR805

SOLD

Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : Used

Description :

2004 Ingersoll-Rand T3W Drill Rig
Engine Hours: 20,621
50 ft – 45,000lb static hook load capacity
hydraulic raise/lower mast
Atlas Topco top drive
Braden 23,000 lb winch
mud system (5” x 6” or 5.5” x 8” GD mud pump)
hydraulic set up to run two pumps or air compressor
hydraulic hoses are re-conditioned
rig derrick can be shortened if requested

Note: no deck engine or air compressor on board the drill
Mounted on International 5600i Truck
Cummins ISX 14.9L Engine
475 Adv horsepower
engine brake
Eaton Fuller 18 speed manual transmission
330” wheel base
8 X 6 20,000lb front axle
54,000lb rears

Location : North America

 

Worldrigs ID: WR768
Model : D120 Drill Rig
Manufacturer : Diedrich
Year : 1991
Condition : Used

Description :

1991 Dierich D120 Drill Rig
John Deere inline 6 diesel Serial #: T06059D43379
990.3 Hours
Moyno 3L8 Pump
500 gallon water tank, Cathead, Fluted kelly, (2) auger racks
Tool boxes, (4) outriggers, 3k, 7k, 10k Winches
Mounted on a 2001 Sterling AT9513 Truck
10 Speed Transmission
Odometer 578,364 miles

Location : USA

Worldrigs ID: WR739
Model : T985HA Rotadrill Rig
Manufacturer : Schramm
Year : 1977
Condition : Used

Description :

1977 Schramm T985HA Rotadrill
Twin Diesel Deck Engine (8V-71)
Twin 400 CFM / 350 PSI Air Compressor (can combine)
Heavy Duty Mast
Autofeed
Auto Hydraulic Table Breakout Wrenches
Twin Hydraulic Main Pump
Twin Hydraulic Top head motors
Top head two speed rotation
Hydraulic adjustable Jib & Swing Jib
Water Injection Pump
Oil Injection Pump
Pull Down & Pull Up Rams
Mounted on a CCC (Crane Carrier Company) Truck 4x4
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR690
Model : T130XD Drill Rig
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm Rotadrill T130XD Drill Rig
Fluid Line Plumbing, Welded
Rotation Guard
Telemast 50 ft
Helpers Platform, Mast Mounted
Mini Lube System
Pullback Limiter
Rotationlock for DH Mtr, w/FS
Slow Feed Drill-Up Valve
Tophead High Cap 4 Meter 4" Tilt
Four Meters, 15/30 cu in
Split Table Assembly, No Slips
Adj Height Brkout Wrnch Mount
Variable Spd Fan (No Comp)
Heater, Diesel Fired Coolant
Spark Arrestor
Note: No Air Compressor on board
Auxiliary Tooling Compressor
Tool Lubricator, Piston Pump
Mounted on a CCC (Crane Carrier) Truck 10x6 ULSD
Aluminum Wheels 10
Heater, Diesel Fired Coolant
ProHeat style Heater for Crane Carrier motor
Pro Heat# PH0403
Jib Boom, Hydraulic Range 2
Hydraulic Pipe Racks, Set (2)
LoadSafe Handler Hydraulic Supply
LoadSafe Pipe Handler
Power Breakout
Remote Hydraulics Supply
Winch, 9,600 lb (150 ft x 1 /2")
Winch, Survey Line

Location : Western Region

Worldrigs ID: WR852
Description :

1989 Schramm T-660 Drill Rig
Detroit 8V92 Diesel Deck Engine (less than 4000 hours since
complete rebuild with preheater)
GHH 900 cfm / 350 psi Air Compressor (Rebuilt, less than 500 hours,
with clutch)
Jib-Boom
Bean water injection pump
360 ft of drill pipe (20ft x 4-1/2"), table bushings & basic tooling included
7 Rod Carousel Lazy Susan
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a GMC White Brigadier Truck (60k+ miles on gauge)
Cat 3208 (Rebuilt transmission less than 2000 miles ago)
Very good tires
Note: Replaced upper chains when the motor were rebuilt about 3500 hours ago

Current repairs needed we are aware of:
Truck CAT 3208 engine starts very hard but once it starts then it runs fine and
runs good (Rebuild time approaching soon)
Traverse cylinders leak small amounts of oil
Deck deck engine leaks small amounts of oil
Compressor clutch work manually only

Location : USA

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR858
Description :

New & Unused 2012 Atlas Copco RD20 Range III XC Drill Rig
Carrier :
Twin H-beam main frame - reinforced 16 in 406.4 mm
5-axle, custom carrier 415 hp 317 kW diesel engine
8-speed transmission Manual with lo - lo and reverse
Tridem rear axles with lockers 23,000 lb each 10,433 kg each
Tandem front steering axles 22,000 lb each 9,979 kg each

Derrick :
Length 61 ft 11 ½ in 18.88 m
Width 4 48 1/2 in 1.23 m
Depth 41 in 1.04 m
Top of table to spindle 51 ft 6 in 5.7 m
Table to ground (rig sitting on tires) 44 in 1,118 mm
Table to ground (jacks fully extended) 92” 2,337 mm

Rig Dimensions :
Height derrick down 13 ft 10 in 4.22 m
Height derrick up 62 ft 6 in 19.05 m
Width 8 ft 4 in 2.54 m
Shipping weight (less tooling) 88,000 lb 40,000 kg

Tip Out Links :
Forged steel 150 ton 136 tonnes
Length 60 in 1,524 mm
Tip out hydraulic cylinder on each link
Angle 0-80° from vertical
Control drillers console

Table & Master Bushing :
Design folding with twin hydraulic jacks
Max opening 26 in 660 mm
API split master bushing 17 ½ in 445 mm
Capacity 60 ton 54.4 tonnes

Rig Performance :
Hookload 120,000 lb 54.4 tonnes
Pulldown 30,000 lbf 13,636 kg
Fast feed up 106 ft/min 32.3 m/min
Fast feed down 180 ft/min 54.9 m/min
Drill feed 29 ft/min 8.8 m/min
Torque 8,000 lbf-ft 10.8 kNm
Speed 0-120 RPM 0-120 RPM
Spindle 3 in 76.2 mm
Swivel Type Multi chevron packings
Opening 2 ½ in 63.5 mm

Location : USA

Worldrigs ID: WR670
Model : SR30 Drill Rig
Manufacturer : Soilmec
Year : 2017
Condition : Used

Description :

2017 Soilmec SR30 Drill Rig
Hours: 1000 (as of Oct 2018)
Cummins QSB6.7-T4F Diesel Engine

Location : Europe

Worldrigs ID: WR202

Model : CTM 10,000 Drill Rig
Manufacturer : DeepRock
Year : 1986
Condition : Used

Description :

Deep Rock CTM 10,000 Drill Rig Package

Package Includes:

Deep Rock CTM 10,000 Commercial Water Well Drilling Rig (Trailer Mounted with Single Axle)
Honda 23 HP engine
Hydraulic Driven
Mission 2 x 1-1/2 Mud Pump
Hydraulic Breakout Wrench
Electric Jib Wrench
Mud Pit
Trailer Mounted

Accessories Include:
2-3/8 x 2-3/8 FMxFM subs
2-3/8 x 3-1/2 FMxFM subs
Drag Bits, 3-1/2 to 6 inch
Tri-Cone Bits, 3-1/2 to 6-1/8 inch
4 inch DTH hammer with 4-1/4 inch Bit
4 inch Shock Absorber sub for D.T.H.
Approximately 200 ft. Drill Rod
Good for drilling shallow Screen Wells & DTH Rock drilling to 150 - 200' ft deep

Included as a Package:

Ingersoll-Rand Gyro-Flo Air Compressor
600 CFM / 100 PSI
Powered by Detroit 671 Diesel Engine
Mounted on a 1974 GMC 6500 Truck
366 Gas Engine (rebuilt with less than 10,000 miles)
Allison 4 speed Transmission
Air Brakes
 
Location : USA

Worldrigs ID: WR881
Description :

2003 Schramm T450 Crawler Drill Rig
Serial Number : J102-B236
Sullair 900 CFM / 350 PSI Air Compressor (serial number: 004-005820) - rated
1800 RPM
Caterpillar 3406B diesel deck engine
Hour meter shows 10,360 hours
Proheat Engine Heater
Bean FMC 2 Cylinder water injection pump
6 Rod Carousel
Graco Hammer Oiler
Pullback: 30,000 lb (13,608 kg)
16.5 inch table opening
Crawler mounted (note: can be mounted on a 2005 Kenworth double frame truck)

Location : USA

Worldrigs ID: WR764
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description :

1994 Ingersoll Rand T4W Drill Rig - S/N: 3909
IR 900 cfm / 350 psi Air Compressor
Cummins KT19 Diesel Deck Engine
Bean Water Injection Pump
Hammer Oilier
4 & 7 Rod Carousel
50,000 lbs of Pullback
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine

Location : USA

Worldrigs ID: WR856
Description :

1992 Ingersoll-Rand T2W Drilling Rig & Package
T2W Drill Outfitted a follows:
IR 900 CFM / 350 PSI Air Compressor
Moyno centrifugal mud pump
500ft of drill pipe on truck (2-7/8” IF), 8-1/2 button bit with stabilizer,
5” hammer, crossover subs included
Mud pan
Mounted on Volvo truck
Cummins N14 diesel engine

Package Includes :
1994 Peterbilt water truck
Grout mixer
2000 gallon in-bed water tank
Auxiliary fuel tank behind cab

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR373

Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
GHH 600 CFM / 250 PSI Air Compressor
CAT D343 Diesel Deck Engine
Mounted on a Kenworth Truck
Diesel Engine

Location : USA

Worldrigs ID: WR861
Description :

Schramm T130 Drill Rig
Diesel Deck Engine
Mounted on a CCC Truck
Diesel Engine

Included as a package:
4-1/2" Bottle Neck X Hole Drill Pipe
6" Collars = 90 ft
All Subs needed to drill
Spare Motor
Spare Parts : Top Drive (Rebuilt no hours), New Spindle,
Bearings for top drive, Chive Crown
Pipe Racks with Catwalk (30 ft L X 5 ft W X 3-1/2 ft T)

Location : USA

Worldrigs ID: WR544

Model: CME-92 Drill Rig
Manufacturer: CME Drill
Condition: Used

Description :

CME-92 Drill Rig
Deck Engine
Mounted on a 5 Ton Chassis Truck
Ford Gas Engine (Model CSG-649P-6006-E)
511,600 km 
3 Hydraulic Leveling Jacks
No Tooling or Hammer will be provided with the unit

Location : USA

Worldrigs ID: WR771
Model : HTB3KDD Drill Rig
Manufacturer : Howard Turner
Year : 2008
Condition : Used

Description :

2008 Howard Turner HTB3KDD Drill Rig Package
CAT C-7 Diesel Engine - rated 260 BHP
6 Cylinder Diesel 2000 MOD NEW
ALLISON-GM MOD # 653
Drawworks :
H.T.B. CANTON TX.
MOD # HTB5KDD - MUSTANG
Clutches - PO3-10
Twin Disk Brakes - 8 x 28 2 per drum
Drums - 14"
Drums - lea bus for 3/4" cable
Drum Drive - 350 hp deran r-angel
25,000 single line pull to 40,000 lbs
Double 120 Chain
Mast : 62ft X 6ft X 3ft HTB - 150,000 #
Carrier : 50ft tandem axle
Swivel : 72 Ton - 144,000 Pounds
JIB Winch
Hydraulics : 20 gpm, 2000 psi. | PTO Driven from Allison Transmission
Drilling Depth : 6,000 feet
Hours : 3087

Extra Item Available(for extra cost) :
2000 Mud Cleaning System FXZ Gardner Denver mud pump
Mounted on a TRA 48ft Trailer 2000 Olympian 60 kW Generator (8,376 Hours)
1990 Ford 9000 - Equipped with winch for loading pipes
Trailer designed for loading pipes with HTB Drilling Rig sold with
2000ft pipes (5” Drill pipe whith 3.5 IF con/ 13.30 lbs)
Tiger 500 Gallon Fuel Tank
Drill colars 6′′ x 28ft ( 2pcs)
3 1⁄2" bottel neck elevators
Pipe Elevators
Drag bit
Tricone bit
Rods 3-1/2′′ x 30ft
Trush Pump
Casing Elevator
Bit 26"
Sub-base

Location : USA

Worldrigs ID: WR629
Model : T985 Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T985 Drill Rig
Dual 425 CFM / 250 PSI Air Compressors
Dual Detroit Diesel Engines
Mounted on a twin axle CCC Truck
Diesel Engine
Working Order

Location : USA

Worldrigs ID: WR209

Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Cummins 4bt 3.9 Diesel Engine @ 100 hp @ 2500 rpm
3l8 Pump
8,500 lbs Main Hoist
29' ft Tower
Mounted on a Ford F800 Truck
5 Speed Transmission
Ford 7.8 Diesel Engine @ 210 hp

Location : USA

 

Worldrigs ID: WR410

Description:

Engine: originally GMC Detroit Diesel, now has a Cummings 6BTA 5.9, Manufacture date of 10/26/1989

Worldrigs ID: WR695
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1978
Condition : Used

Description :

1978 Chicago-Pneumatic Model 650 S/S Drill Rig
Caterpillar 3406 diesel engine - serial number 9HB03011
Near new batteries
750 CFM / 125 PSI CO5 Air Compressor
Dynex main pump & Dynex Head motor
Hydraulic winch
27,500 lb. pullback capability
DTH Hammer oiler
4-hole Funk Box (hydraulic pump drive)
REICHdrill dust collector (can be removed if needed)
Operators cab (can be removed if needed)
6-pod drill pipe carousel
Comes with 3 near-new 25 ft. x 5 in. OD drill pipes
New head adapter
New bit sub (tricone bit not included)
3 Hydraulic jacks
Mounted on a 1978 FCCC (Crane Carrier Company) truck
powered by Caterpillar 3208 diesel engine
13-speed Roadranger transmission
showing only 3934 miles on odometer
We also have used 25 ft. length x 4-1/2 in. OD x 3-1/2 in. API Regular
drill pipe available which can be sold at an extra cost, if needed.

Location : USA

Worldrigs ID: WR798
Model : CM-780D Blasthole
Manufacturer : Ingersoll-Rand
Year : 2003
Condition : Used

Description :

2003 Ingersoll-Rand CM-780D Blasthole Drill Rig
Crawler Mounted
Caterpillar Diesel Engine
S/N: G78255EL
IR HR2 865 CFM / 350 PSI Air Compressor
Water injection
Hammer Lubricator
Thread Greaser
Enclosed Cab
A/C & Heater
Rod Changer
13-1/2" Track Shoes
Set up for (3-1/2”O.D. x 13.1ft) Drill Pipe 21/2Z thread
Meter Reads 15,940 Hours

Location : USA

Worldrigs ID: WR456

Worldrigs ID: WR786
Model : 10R Drill Rig
Manufacturer : Bucyrus Erie
Year : 1972
Condition : Used

Description :

1972 Bucyrus Erie 10R Drill Rig
Started rebuild
Needs back out riggers
No air, or MP
Runs Drives Wont take much to be Drill Ready
Not many hours on this rig for its age

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR649
Model : KAT.ST.250 Drill Rig
Manufacturer : Generic
Year : 2018
Condition : New

Description :

2018 KAT.ST.250 Fully Hydraulic Drill Rig
Engine: Aircooled  MAGIRUS  DEUTZ   125  HP
Rotary head torque: 3,800 Nm
Rotary head stroke : 3.35 m.
Pull back capacity: 11.5 ton
Pull down capacity: 7 ton.
Max. drill pipe length : 3 m
Foam pump 50 Bar options

This particular drill rig can be operated in three different modes (Using optional equipment)
1) Water drilling
2) Compressed air and foamdrilling
3) Compressed air and hammer drilling

Location : Eastern Europe Region

Worldrigs ID: WR757
Model : T500XD Telemast Drill Rig - Trailer Mounted
Manufacturer : Schramm
Condition : New

Description :

New 2015 Schramm T500XD Telemast Drill Rig
Trailer Mounted
Rated 1520 HP Diesel Power
60° PAD Walking System
Tilting Top Drive
Control Room
Loadsafe® XD Automated Pipe Handling System
Hands Free Power Breakout
500,000 lbs. (226,796 kg) hook load rig in a portable over the road package
80,000 lbf. (356 kN) hydraulic pulldown for precise weight on bit control
Control cabin with joystick controllers for drilling and pipe handling
operations Self-erecting in a matter of hours without the use of a crane
Power breakout, table and slips maximize safety on the drill floor
LoadSafe XD hands-free Range III pipe handling system included
Crew of three typical
Optional dual fuel configuration available
no draw works on this rig, has hyd powered hoist and rotation

Note: Major Price Reduction to Sell Quickly

Expected fuel consumption per hour?
Model: MTU 12V-2000TA DDEC Tier 1
Power: 760 bhp (567 kw) @ 1,800 rpm
Torque: 2,188 ft-lb (2,967 N-m) @ 1,800 rpm
Displacement: 1,458 cu. in. (23.9 l)
B.S.F.C.: .338 lb/bhp-hr @ Maximum Power (206 g/kw-hr)
Fuel Consumption: 36.2 g/hr @ Maximum Power, 27 g/hr @ Average Load
Horsepower Ratings: +2%, -0%
Altitude Performance, All MTU Series 2000 Engines - % of Rated BHP:
5,000ft (1524m) = 99.0% at 1800 rpm
10,000ft (3048m) = 97.0% at 1800 rpm
15,000ft (4572m) = 94.5% at 1800 rpm

Location : USA

Worldrigs ID: WR799
Model : T4W LT Range II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2005
Condition : Used

Description :

Ingersoll-Rand T4W LT (Long Tower) Range II Drill Rig
2005 CAT C-12 Diesel Engine (4,000 hours)
Ingersoll-Rand 1170 cfm / 350 psi Air Compressor
70,000 lbs of Pullback (Deep Hole)
4 hole gearbox and 2 hole gearbox
High Torque Spur Gear power head with cushion sub
Bean Water Injector Pump rated at 2000 psi
Mounted on a CCC (Craine Carrier Company)
CAT 3406 Diesel Engine
2400 Gal Fuel Tank with Hose Reels
12V Electric Pump

Mounted on a 32 ft Tandum Axle trailer
Sullair 1150 cfm / 350 psi Air Compressor
CAT C-15 Diesel Engine with 7,000 hours

Hurricane Booster - rated 900 lbs of pressure
CAT 3126 Diesel Engine
Both mounted on a 32' ft Tandum Axle Trailer

120 Pipe of T4 style drill pipe (3,000 ft) 3-1/2" Reg Pin and Box
5 check valve subadapters
Pipe and adapters are all loaded on 2 tandum axle flat bed trailers
Drill Rig Base or Platform
14" tall 35 ft long 10 ft wide with folding ramps and fold down walkways
38 ft tandum axle trailer with roller for moving
IR-120 Hammer with 12-1/4" bit x 11" x 20 Stabilizer
IR-TD-90 Hammer with 8-7/8" bit x 8" x 20 Stabilizer
IR QLX-60 Hammer w/ 6-1/4"bit, 6" by 25ft Stabilizer
3 sets of Casing Clamp type Elevators for 4-1/2", 7" & 9-5/8"
Washington rotation head diverter assembly with adaptter plates
35 ft of blow pipe with hammer unions
2 complete Petol wrenches, Misc Table bushings & Wrenches Forks and Subs

Location : USA

Worldrigs ID: WR856
Description :

1992 Ingersoll-Rand T2W Drilling Rig & Package
T2W Drill Outfitted a follows:
IR 900 CFM / 350 PSI Air Compressor
Moyno centrifugal mud pump
500ft of drill pipe on truck (2-7/8” IF), 8-1/2 button bit with stabilizer,
5” hammer, crossover subs included
Mud pan
Mounted on Volvo truck
Cummins N14 diesel engine

Package Includes :
1994 Peterbilt water truck
Grout mixer
2000 gallon in-bed water tank
Auxiliary fuel tank behind cab

Location : USA

Worldrigs ID: WR857
Description :

1973 Gardner Denver 14W Drill Rig
Mounted on a CCC (Crane Carrier Company) Truck
390 ft of Drill Pipe included
Mud Pit & Tee
1000 cfm / 250 psi Air Compressor  
Gardner Denver 5x6 Mud Pump
Bean Water Injection Pump
Cummins 350 Diesel Engine
Foller 13 Speed Transmission
Hour meter reads 1978 Hours
Mileage reads 18,687 Miles
Newer Front tires

Location : USA

Worldrigs ID: WR885
Description :

1986 Jaswell J1200 Drill Rig
Mounted on a 1986 International Paystar 5000 Truck
Cummins 350 HP diesel engine  
20 speed spicer transmission
20k front axle & 44k rear axles
Odometer works and reads 96,000 miles
90% rubber all around
Cummins N14 mechanical - rated at 450 HP diesel engine
Sullair 900 cfm / 350 psi air compressor with cooler mounted on the side

Comes with : 360 ft of drill steel, two 6" hammers, and 8" hammer stabilizer
6" QL60 Hammer and the 8" Hammer & 8-1/2" Bit. All hand tools included
New diamond chains top and bottom, new sprockets, pins and bushings in 2018
Rebuilt twin disc pto in 2018. Replaced rear main seal in the deck engine 2018
New crown shaft in 2018, pillow block bearings were used but in good condition
Two piston bean pump. Tube style tower same as J2400
1000 hours on it since repairs in 2018

Location : North America

Worldrigs ID: WR788
Model : 30K Drill Rig
Manufacturer : Gefco
Year : 2000
Condition : Used

Description :

2000 Gefco / Speedstar 30K Drill Rig
Top head power drive (has been gone through)
6250+ hours
Mounted on a 2000 Peterbilt 357 Truck
CAT C-15 diesel engine
Sullair 1000 cfm / 350 psi air compressor
Newer Oil Cooler
(12,500+ Hours & 102,250+ Miles on gauge)
30,000 lbs of pullback
Hydraulic Leveling Jacks
Package Includes:
Beals & Welco casing hammer (Casing hammer not in the tower but included)
500 ft of drill pipe, 2 drill collars, and basic tooling

Location : USA

Worldrigs ID: WR780
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
mounted on an IH Truck
All original parts
Head need work
Good Parts Machine

Location : USA

Worldrigs ID: WR373

Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
GHH 600 CFM / 250 PSI Air Compressor
CAT D343 Diesel Deck Engine
Mounted on a Kenworth Truck
Diesel Engine

Location : USA

Worldrigs ID: WR839
Description :

LTD 360 Cable Drill Rig
Carries enough mainline cable to drill to a depth of 450 feet
Bore diameters of 4" to 10" inches
Lift capability of 8,000 lbs for casing removal
40 gallons of on-board water storage with a 40 PSI pump
150 amp arc welder when steel casing is used
20 gallons of fuel (enough to drill about 75 feet)
Rated - Penetration rates usually range between 2-½-5 feet per hour
depending on the geology/ground formations with drilling conditions
Mounted on a 2 axles trailer

Location : USA

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR763
Model : M8A Drill Rig - Table Drive
Manufacturer : Davey
Year : 1965
Condition : Used

Description :

1965 Davey M8A Drill Rig
Davey Piston Air Compressor
Serial Number: 381
300 CFM / 100 PSI Piston Air Compressor
Detroit 6-cylinder Diesel Engine Deck Engine
20 ft. kelly bar - Table Driven
Set up to run (15 ft. x 4 in.) OD drill pipes
Comes with 240 ft. of drill pipe in Rod box
DTH Hammer Oiler Working Condition
Mounted on a 1995 Ford Truck
Diesel Engine
12R22.5 tires
Mileage 99,202 miles
Dimensions: 34ft x 8ft 5" x 13ft
Note: hasnt drilled since late 2017

Location : USA

Worldrigs ID: WR77

Model : T-555
Manufacturer : Schramm
Year : 2002
Condition : Used

Description :

2002 Schramm T-555 Drill Rig
Sullair 1070 CFM / 500 PSI Air compressor,
75,348 in lbs torque @ 0-131 RPM,
40,000 pullback,
30,000 pulldown.
CAT C-15 DIT Diesel Deck Engine @ 565 HP with 6,326 Hours
18 GPM Bean water pump
280' ft of (4 1/2 rod with 3 1/2 IF pin, box ends).
Note: can hold 300' ft in the rod box and can run 20" Casing pipe
DTH oilier, Sandline Semco S6
Hydraulic swing and extend Jib boom
Secondary winch Pullmaster M8-3-30-1
Primary winch
Mounted on a 2002 International 2674 Truck
Powered by Cummins ISM370 Diesel Engine
21,529 miles

Location : USA

Worldrigs ID: WR604
Model : T450 Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T-450 Drill Rig
Holte Casing Hammer
Diesel Deck Engine
Air Compressor is low pressure
Mounted on a Truck
Diesel Engine
53,784 Miles on gauge

Could be sold as a package:
Drill Pipe 600’ ft of 4-1/2” & 185’ ft of 3-1/2”
Tulsa Rig Iron Mud shaker
Pipe Truck
assorted bit and reamers

Location : USA

Worldrigs ID: WR837
Description :

Geoprobe 8150LS Crawler Drill Rig
Geoprobe 50DT Track Base Platform
Geoprobe GV5 Sonic Head Long Stroke
Geoprobe Designed Rod Handling
System Head Feed Stroke: 157"
50K Dynamic Force
Remote Diagnostics
Adjustable Swing-arm Control Panel
Automatic Drop Hammer 140 lb
Winch Kit: 2,500 lb

Safety Cage
Triplex High Pressure Water Pump
Air Compressor Kit, C6.6 with BA-922
Drop Rack System with Rod Rack
Drill Mast Side-Shift
Head Centerline Side-Shift
Fits in 40 ft Shipping Container for Exporting
10-ft Tooling Compatible
Rock Coring Compatible
14" in Double Wrench Breakout

Dual Winch System
Front and Rear Outriggers (Four Point Stabilization)
Sonic tooling inventory with rig: (extra cost or included as a package)
Two tooling indexing racks with rollers
230 ft of 4 tooling
230 ft of 6” tooling
100 ft of 8” tooling
One Actuator core for rod handler
One SDT-60 Weighted Wire Line Core Barrel
Several bits and adapters
(Cost Extra or included as a package for all listed together)
2010 Freightliner model Cascadia Truck with Diesel Engine (492,560 miles)
Trailer for the hauling the drill, pipe, and tooling (as is in the pictures)
1210 Hours on Engine, 210 Hours on Sonic Head at time of listing.

Location : USA

Worldrigs ID: WR827
Description :

1979 Jaswell 1200 Drill Rig
Mounted on a Paystar 5000 Truck
Detroit 8V92T Diesel Deck Engine (newer clutch)
Sullair 900 cfm / 350 psi Air Compressor (Recent Compressor and Radiator)
New Chains and updated pumps, gear box
Has cat walk
Recent Oil change
Mounted on a Paystar 5000 Truck
Detroit 671 turbo diesel engine
newer rear tires
5 +4 Transmission
All newer paint

Location : USA

Worldrigs ID: WR786
Model : 10R Drill Rig
Manufacturer : Bucyrus Erie
Year : 1972
Condition : Used

Description :

1972 Bucyrus Erie 10R Drill Rig
Started rebuild
Needs back out riggers
No air, or MP
Runs Drives Wont take much to be Drill Ready
Not many hours on this rig for its age

Location : USA

Worldrigs ID: WR518
Details:

Worldrigs ID: WR664
Model : 2800 HS (HT) Drill Rig
Manufacturer : Simco
Year : 1992
Condition : Used

Description :

1992 Simco 2800 HS (HT) Drill Rig
Deutz diesel engine on deck
3L6 Moyno pump
Mounted on rubber carrier, powered by 243 Ford gas engine
This rig has been used as recent as February
May have a small oil leak but is all we know that is wrong with it.

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR546

Model : D40K Drill Rig
Manufacturer : Driltech
Condition : Used

Description :

Driltech D40K Drill Rig
50,000 lbs of pullback
high torque head
No carousels (removed for large diameter Well drilling)
dual winches 6000k single line
18000K single line hydraulic Denison P7 main pump - replaced early p-5
All pumps where rebuilt or replaced in 2015 including main gearbox rebuild
Replaced / upgraded to Mercedes tier 4 (I) 550hp diesel deck motor
900 CFM / 300 PSI air compressor
has a mud line and a true 3" mud swivel added to it so it's "mud ready"
New in 2015 radiator/engine cooler rated at 450hp Additional hydraulic cooler added
Mounted on 2012KW tier 4 435hp Paccar heavy spec truck
dual steering and full locking rears
Heavy duty engine Brake
Rig needs a few new hydraulic hoses and new paint job
Note: this machine is 100% California CARB compliant

Location : USA
 

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR769
Model : Drill Rig
Manufacturer : Gus Pech
Year : 2008
Condition : Used

Description :

2008 Gus Pech Drill Rig
5,000+ Hours / Miles on Freightliner Truck
3,500+ Hours Drill
Overhauled at Gus Pech Factory in 2017
Sullair 700 cfm / 200 psi Air Compressor
7x10 Centerline Mud Pump
Tilt Power Head
450 hp Mercedes Diesel Engine
set up for Water Wells
estimated rig weighs 48660 lbs, 8ft 6” W, 13ft H, 37ft L

Location : North America

Worldrigs ID: WR102

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1987
Condition : Used

Description :

1987 Ingersoll-Rand T3W Drill Rig
S/N: 2713
Cummins 855 Diesel Engine
IR 825 CFM / 350 PSI Air Compressor (Rebuilt 300 Hours Since)
300' ft of used drill pipe (20' x 4-1/2") included
Hammer lubricator
26,500 lbs of pull back
Mounted on a Ford 8000 Truck
Diesel Engine
VIN# 1FDXR82A5HVA24572
8 Speed Transmission

Missing the following main components:
3 Hydraulic Jacks, No top head motors & pulleys, cable pulleys
from main hoist, hydraulic pump missing from the funk box,
no hydraulic cooler, fork wrench, triple pump, gauges, air switch,
regulator, water injection pump, foot valve, cooler leaks and
feed cylinder leaks, etc.

Location : USA

Worldrigs ID: WR781
Model : DSI QuikDrill Rig
Manufacturer : Speedstar
Condition : Used

Description :

Speedstar DSI QuikDrill
Failing FM-3 Mud Pump
Has Air Compressor (Not Working)
Mounted on 2001 International 4900 Truck
Powered by 7.6 L 466 CID L6 International DT466 Diesel Engine

Location : USA