Worldrigs ID: WR216

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description :

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR762
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 Range III Drill Rig & Pipe Handling System
Hours 27,319+
Heavy‐duty Derrick and Top head Drive pullback of 120,000 lb
51 ft. 7" in. clearance - plenty of room for 30 ft. drill pipe
8,000 ft‐lb. Spur gear power head
Cummins QSK‐19C Diesel Deck Engine - rated 755‐hp
IR HR2.5 1,250 cfm / 350 psi Air Compressor over/under Air End
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar C13 Diesel Engine - rated 380 HP
Mileage  32,531+
Note: Package Includes:
2014 Foremost Pipe Handler 4000 Series (hydraulic pipe handling system -
hands free) on a 2 axle Trailer
The engine, compressor and hydraulic pumps are mounted on a floating
power‐pack

Location : USA

Worldrigs ID: WR877
Description :

2015 Atlas Copco Pit Viper 235 Drill
Pressure: 350 psi
Flow: 1.450 cfm
Approx 11.000 Working Hours

Location : South America

Worldrigs ID: WR604
Model : T450 Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T-450 Drill Rig
Holte Casing Hammer
Diesel Deck Engine
Air Compressor is low pressure
Mounted on a Truck
Diesel Engine
53,784 Miles on gauge

Could be sold as a package:
Drill Pipe 600’ ft of 4-1/2” & 185’ ft of 3-1/2”
Tulsa Rig Iron Mud shaker
Pipe Truck
assorted bit and reamers

Location : USA

Worldrigs ID: WR178

Model : 1250 Drill Rig
Manufacturer : Failing
Condition : As-Is

Description :

(1) Failing 1250 Drill Rig (being sold for parts)
No Rotary Table
No Mud Pump
No Transfer Case
No Kelly
No Chains
(Basically If You Need A Tower Or Something)
Mounted on a International Truck
Diesel Engine
(1) International 1500 Galloon Water Truck
10 Wheel
Water tank built to bed -O- to haul from pipe beside tank

Location : USA

Worldrigs ID: WR842
Description :

2002 Ingersoll-Rand T4W Drill Rig
Cummins QSK-19-C Diesel Deck Engine (rated 600 HP at 2100 RPM)
IR HR2.5 1070 cfm / 350 psi Air Compressor
Mounted on a CCC (Crane Carrier)
CAT C-10 Diesel Engine
50,000 lbs of Pullback
Dual Motor Planetary Head
Setup for 2-7/8" IF Drill Rod
Recently painted silver and red

Additional Tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Miller Welder with Leads
Oxy/Acetalene Torch Setup

Location : USA

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR610
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used

Description :

1989 Ingersoll-Rand TH60 Drill Rig
Ingersoll-Rand 825 cfm / 350 psi Air Compressor
Gardiner Denver 5x6 Duplex Power Mud Pump
Pulse Injection Pump 1lt/min - rated 70bar
Cat Water pump 38 lt/min - rated 69 Bar
Gearmatic Winch Model 35 single speed with automatic brake and free-fall attachment 12000 kg @22 metres /min.
Capacity 112 metres of 14mm cable
Weldco Casing Hammer
Pulldown (30,000lbs) 13,610 kg. & Holdback (30,000lbs) 13,000kg
Rotation torque (60,000 in-lb) 692 kg-m & Rotation speed 0-100 rpm
Mounted on a Hendrickson Truck (8x6) 6 wheel drive
Detroit 8V92TA V8 Diesel Engine - rated 427 hp
400' ft of drill pipe & tooling & spare parts are included

Location : Western Region, Europe

Worldrigs ID: WR789
Model : TLS Drill Rig
Manufacturer : PortaDrill
Year : 1978
Condition : Used

Description :

1978 PortaDrill TLS Drill Rig
Rebuilt - Volvo Diesel Deck Engine - rated 500 HP
500 ft. of 3-1/2" inch Drill Pipe included
Pipe Rack
Top head was rebuilt in summer 2018
New Water Injection Pump installed in summer 2018
Mounted on a Truck
Cummins diesel engine

Location : USA

Worldrigs ID: WR772
Model : 14W Drill Rig
Manufacturer : Gardner Denver
Year : 1971
Condition : Used

Description :

1971 Gardner Denver 14W Drill Rig
Rig Engine: 350 cummings 855 Diesel
Has 8500 hours
10” rotary table
5 X 6 gear driven Gardner Denver mud pump
600 cfm / 250 psi GD air compressor with blower
600ft of 4-1/2” X 15ft drill pipe and break out tooling / 24ft Kelly
In good working order, ready to drill today
Arc welder is not included.
Package Includes 2 Support Trucks

Location : USA

Worldrigs ID: WR628
Model : T64HB Drill Rig
Manufacturer : Schramm
Year : 1969
Condition : Used

Description :

1969 Schramm T64 Drill Rig
Detroit 8V71 diesel deck engine
425 cfm / 250 psi air compressor
300 ft of 4-½inches x 20ft drill pipe
6inches hammer w/ 6inches bit
8inches hammer w/ 8inches bit
2 new motors on head
Last had it running in mid-January 2019
Mounted on a newer 1995 Ford 9000 Truck
Cummins N14 diesel engine
9-speed transmission
2250 tires (estimated 85% good)

Location : USA

Worldrigs ID: WR861
Description :

Schramm T130 Drill Rig
Diesel Deck Engine
Mounted on a CCC Truck
Diesel Engine

Included as a package:
4-1/2" Bottle Neck X Hole Drill Pipe
6" Collars = 90 ft
All Subs needed to drill
Spare Motor
Spare Parts : Top Drive (Rebuilt no hours), New Spindle,
Bearings for top drive, Chive Crown
Pipe Racks with Catwalk (30 ft L X 5 ft W X 3-1/2 ft T)

Location : USA

Worldrigs ID: WR499

Model : T64 HB Drill RigB Drill Rig
Manufacturer : Schramm
Year : 1978
Condition : Used

Description :

1978 Schramm T64HB Drill Rig
GHH 425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Cat water injection pump
2 motor power head
260' ft of  (4-1/2” x 20’ x 3-1/2" API reg thread)
Mounted on GMC 7500 Truck
Powered by Detroit 6V53 Diesel Engine
13 speed transmission

Location : USA
 

Worldrigs ID: WR880
Description :

1984 Speedstar Quickdrill 600 Drill Rig
Mounted on an International 2574 Truck
Rebuilt - Detroit 8V92 Deisel Engine with Jake brakes
Rebuilt - Eaton Fuller 13 speed transmission with new clutch-throw out bearing
All new coolant-oil hoses, radiator, exhaust from turbo to muffler, drive shafts, &
rear end
Feed-outrigger-jib-rod jaw-tower hydraulic cylinders and hoses all new
Fully rebuilt top head - gears, bearings, seals, hydraulic motors, north Houston
machine under head mud and air swivel all new. New high pressure airline and
fittings from compressor to top head.
10 GPM water injection pump - completely rebuilt
12,000 lb main winch fully rebuilt including all bearings, seals, and hydraulic motor.
Rebuilt rod box
New oil filters on compressor
600 cfm / 250 air compressor
500 ft 3-1/2” OD by 2-3/8 IF drill rods
table bushings, etc.
Drive traction tires 60% percent & Steer tires 80% percent estimated

Location : USA

Worldrigs ID: WR664
Model : 2800 HS (HT) Drill Rig
Manufacturer : Simco
Year : 1992
Condition : Used

Description :

1992 Simco 2800 HS (HT) Drill Rig
Deutz diesel engine on deck
3L6 Moyno pump
Mounted on rubber carrier, powered by 243 Ford gas engine
This rig has been used as recent as February
May have a small oil leak but is all we know that is wrong with it.

Location : USA

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR763
Model : M8A Drill Rig - Table Drive
Manufacturer : Davey
Year : 1965
Condition : Used

Description :

1965 Davey M8A Drill Rig
Davey Piston Air Compressor
Serial Number: 381
300 CFM / 100 PSI Piston Air Compressor
Detroit 6-cylinder Diesel Engine Deck Engine
20 ft. kelly bar - Table Driven
Set up to run (15 ft. x 4 in.) OD drill pipes
Comes with 240 ft. of drill pipe in Rod box
DTH Hammer Oiler Working Condition
Mounted on a 1995 Ford Truck
Diesel Engine
12R22.5 tires
Mileage 99,202 miles
Dimensions: 34ft x 8ft 5" x 13ft
Note: hasnt drilled since late 2017

Location : USA

Worldrigs ID: WR826
Description :

2006 Simco 2800HT Drill Rig,
Automatic hammer,
Extruder,
Hydraulic clamps (newer),
Gardner Denver 4-1/2x5 mud pump,
Slide base and head tilt,
2 winches,
High Torque head.
New MAST extension 3 pulleys.
Mounted on a Ford F550 Truck,
Diesel Engine,

Location : USA

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR672
Model : R-620 Drill Rig - Crawler
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec R-620 Crawler Drill Rig
Hours: 6,200
R-620
Hydraulic Drilling Rig
A new model : The R-620 drilling rig on caterpillar 3.30C high power
module has been designed to perform the follwing jobs:
Bored pile, with dry or bentonite system;
Bored pile, with casing installed by oscillator or rotary crowd system;
C.F.A (Continuous flight Auger) piles.

The main features of R-620 are the following:
Machine class: 60 tons
New machine caterpillar type 3.30C module c/w diesel engine and
sound proofed canopy,mounted on 360 degrees slew ring
New electronic engine C9 ATAAC wth more power(355Bhp) and
meeting the most recent emission regulations.
New powerful rotary:201 kNm
Completely self erecting;mast able to withstand the max torque
over the whole length.
Casing installation by rotary crowd system
Advanced instrumentation
Reliability and safety
Stability and easy to handle
High productivity
Easy to transport
cable crowd system(optional)
Mechanical and hydraulic pre - arrangement for casing
oscillator(available on request)
 

Large diameter bored pile
Max pile diameter	mm	1800
Max cased diameter	mm	1500
Max pile depth	m	66
Max nominal torque	kNm	201
Max drilling speed	rpm	34
Spin off	rpm	144
Main winch nominal line pull	kN	192
Service winch nominal pull	kN	80
Engine¹	type	Caterpillar C9 ATAAC-HEUI
Max power	Kw (bhp)	261(355)
Crowd system by cylinder	kN	210/150
Pull  down stroke	mm	5600
Cable crowd system(13m stroke)	kN	200/200
Operating weight	ton	63

 

Continuous Flight Auger (CFA)
Max pile diameter	mm	900/1000
Max pile depth	m	22.5
Max nominal extraction force	kN	600
Max nominal torque	kNm	201
Max drilling speed	rpm	34
Operating weight	ton	60-63

 

Location : USA

Worldrigs ID: WR797
Model : TXD Drill Rig & Package
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm TXD Drill Rig Package
Deck Engine : Detroit Diesel DDC/MTU 12V-2000

Tilting Top Head Drive : Heavy duty, single reduction gearbox
with 4 two-speed disc valve type hydraulic motors  
variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM  

Feed System : 50 ft (15.24 M) head travel  
200,000 lbf (890 kN) hoist capacity  
100 fpm (30.5 m/min) hoist speed  
32,000 lbf (142 kN) pulldown  
200 fpm (61 m/min) pulldown speed

Drill Table : Table Opening: 30 inches (768 mm) diameter with table retracted  
Hydraulically retractable slip box

Drill Pipe and Casing : Range III tubular capability  
30 inch

Winch : Planetary design with spring applied hydraulic release brake ·
9,600 lbf (42.7 kN) bare drum line pull  
150 fpm (46 m/min) bare drum line speed  
Hydraulic jib boom swing and extend  
Auxiliary winch available

This drill has low wear, Cables and bearing and pivot points,
Control panel all are in excellent condition.
Hoses are getting older.
Mounted on a Trailer
LoadSafe pipe handling systems
Generator house 2 155KW Generators powered by Perkins IR Shop Air,
Hydraulic lift jacks and 3 stage closing unit.
500 HP Mud pump Weatherford T425 powered by John Deere 61356.50 Plunger 900 PSI,
MCM 4x5x14 Super Charge pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House
8000 ft  of drill pipe
4 - 6-1/2” Drill collars
Every pcs is clean and straight nice package.

Location : USA

Worldrigs ID: WR800
Model : 1500 Drill Rig
Manufacturer : Midway
Condition : Used

Description :

Midway 1500 Drill Rig
10" table retracts but needs cylinder
5-1/2 x 8 GD Pump
New transfer case
4 jacks
Long Derrick
Long Kelly
500 of 2-7/8" drill pipe
Auto car
Caterpillar 3406 Diesel Engine
Bill of sale only

Location : USA

Worldrigs ID: WR865
Description :

UDR 1500 Range III Mobile Drill Rig
Mounted on a 2004 International 5800i Tri-Axle Truck
Engine Hours : 11,804
75 ft - 90,000 lb static hook load capacity
hydraulic raise and lower mast
Rexroth 44,000 lb draw works
Top drive
GD mud pump
CAT C15 14.6L diesel engine
525 Adv horsepower
Engine brake
Eaton Fuller 18 speed manual transmission
352” wheel base
40,000 lb front axle
51,000 lb rears
Rig was almost completely overhauled . Hydraulics , hoses, box  etc.

Location : North America

Worldrigs ID: WR690
Model : T130XD Drill Rig
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm Rotadrill T130XD Drill Rig
Fluid Line Plumbing, Welded
Rotation Guard
Telemast 50 ft
Helpers Platform, Mast Mounted
Mini Lube System
Pullback Limiter
Rotationlock for DH Mtr, w/FS
Slow Feed Drill-Up Valve
Tophead High Cap 4 Meter 4" Tilt
Four Meters, 15/30 cu in
Split Table Assembly, No Slips
Adj Height Brkout Wrnch Mount
Variable Spd Fan (No Comp)
Heater, Diesel Fired Coolant
Spark Arrestor
Note: No Air Compressor on board
Auxiliary Tooling Compressor
Tool Lubricator, Piston Pump
Mounted on a CCC (Crane Carrier) Truck 10x6 ULSD
Aluminum Wheels 10
Heater, Diesel Fired Coolant
ProHeat style Heater for Crane Carrier motor
Pro Heat# PH0403
Jib Boom, Hydraulic Range 2
Hydraulic Pipe Racks, Set (2)
LoadSafe Handler Hydraulic Supply
LoadSafe Pipe Handler
Power Breakout
Remote Hydraulics Supply
Winch, 9,600 lb (150 ft x 1 /2")
Winch, Survey Line

Location : Western Region

Worldrigs ID: WR689
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1979
Condition : Used

Description :

1979 Ingersoll-Rand TH60 Drill Rig
IR 750 cfm / 250 psi Air Compressor - 2 Stage Screw type
Gardner Denver 5X6 Mud Pump (hydraulic driven)
Mounted on a newer 1995 Kenworth T800 Truck
Cummins N14 Diesel Engine - rated 425 HP
4-Motor Tophead with 2-7/8" Threads
200 ft of 20ft x 4.5" x 2-7/8" Drill Pipe
20K Front End
40,000 lbs of Pullback
Rod Box
7-Rod Carousel
Bean Water Injection
Sand Line
Auxiliary PTO for Lift Pump
Two Brand New Batteries
Note: Capable of Handling a Casing Hammer (not included)
2,080 Total Hours (600 hours on it since rebuild in Feb. 2015)
Meter Reads 9,734
The truck is all original
Note: Can be Sold with a service truck and water truck at an extra cost

Location : USA

Worldrigs ID: WR855
Description :

1976 Ingersoll-Rand Cyclone TH60 Drill Rig
Leroi 450 CFM / 250 PSI Air Compressor
Hydraulics and Compressor are PTO powered by truck engine
Mounted on International Paystar truck
8V92 Detroit diesel engine with Jake brake
13-speed Eaton fuller transmission
Front tires 4 years old, Rear older but good tread
(Drive tires in pic are not current)
Air over hydraulic for controls
980 ft sand line new 2 years ago
Main winch cable needs replacing soon (unknown age)
Pull back cables new 3 yrs ago
New swivel bearings and seals in Feb this year
New water pump 3 yrs ago
Regularly service
Hours unknown
Some gauges work some dont
Has some oil leaks in hydro system
Its ready to drill

Location : USA

Worldrigs ID: WR804
Model : 2500 Drill Rig
Manufacturer : Gardner Denver
Year : 1985
Condition : Used

Description :

1985 Gardner Denver 2500 Drill Rig
Cummins - rated 400 HP
three speed Allison (750) auto transmission
Diesel tank on rig
100 ton McKissich (shorty) blocks with 7/8” cable
Weight indicator
4 hydraulic leveling jacks
Tongs
Hydraulic raise and cable telescoping 67 ft mast
Mounted on a 2 axle trailer
130,000 lbs. mast
18” Gardner Denver rotary table
Tongs with air cathead make up and air cathead breakout
1 – Swivel
1 – 40ft x 3-½” IF Kelly with bushing
Rat hole digger
Rat hole shuck

Location : USA

Worldrigs ID: WR586

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description :

1994 Ingersoll-Rand T3W
CAT 3406C diesel deck engine (7,000 hours since rebuilt)
IR 825 cfm / 350 psi Air Compressor (4,300 hours since rebuilt)
8,000 lb rotary head
7 rod carousel
rod box
25 GPM Water Injection Pump
Hammer Lubricator
18,000 lb single line winch
Newer Tires
Newer Paint
Mounted on a Ford L9000 Truck
CAT 3176 diesel engine
Eaon 13 speed transmission
9,106 miles on odometer (may be incorrect)
Note: Rig was thoroughly reconditioned by manufacture in 2015 and has only been
used a few hours since

Location : USA

 

Worldrigs ID: WR772
Model : 14W Drill Rig
Manufacturer : Gardner Denver
Year : 1971
Condition : Used

Description :

1971 Gardner Denver 14W Drill Rig
Rig Engine: 350 cummings 855 Diesel
Has 8500 hours
10” rotary table
5 X 6 gear driven Gardner Denver mud pump
600 cfm / 250 psi GD air compressor with blower
600ft of 4-1/2” X 15ft drill pipe and break out tooling / 24ft Kelly
In good working order, ready to drill today
Arc welder is not included.
Package Includes 2 Support Trucks

Location : USA

Worldrigs ID: WR600
Model : T450BH Crawler Drill Rig
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T450BH Crawler Drill Rig
CAT 3406C diesel engine (newly rebuilt - couple hundred hours on engine)
Sullair 900 cfm / 350 psi Air Compressor (3000 hours since rebuilt)
Hours: 8000 or a little less.
Dust Collector
5-Rod Carousel
Everything is in good working order.
100 ft of Schramm Drill Rods (25 ft. length x 4-1/2 in.) & QL60 6-1/4" bits

Location : USA

Worldrigs ID: WR790
Model : 500 Drill Rig
Manufacturer : Midway
Year : 1969
Condition : Used

Description :

1969 Midway 500 Drill Rig
Mounted on 1969 Peterbilt Truck
Leroi 100S Air Compressor
Gardner-Denver 5x6 Duplex Piston Mud Pump
New Rear Jacks
Recent Cummins Swap
Transfer case rebuilt in summer 2018
Comes with 200 ft. of 2-7/8” drill pipe
Currently working
Ready to drill

Location : USA

Worldrigs ID: WR773
Model : T64HB Drill Rig - Retrofitted
Manufacturer : Schramm
Year : 1978
Condition : Used

Description :

1978 Schramm T64HB Drill Rig - Retrofitted in year 2000
Detroit 8V92 diesel deck engine
T660 Derrick replaced the T64HB Derrick
Sullair 900 cfm / 350 psi Air Compressor
Carousel
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a 1986 Ford L8000 Truck
CAT 3208 diesel engine
13 speed Eaton fuller transmission

Location : USA

Worldrigs ID: WR684
Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Moyno water pump
Cummins Diesel deck engine
Detroit 671 T Diesel Engine in truck
140 lb. Safety Hammer
100 ft 6-5/8” augers
rods, bits, etc. included

Location : USA

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR315

Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New

Description :

Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires

Location : USA

Worldrigs ID: WR776
Model : SDC500-29P Drill Rig
Manufacturer : Sonic
Condition : Used

Description :

Sonic SDC500-29P Drill Rig
80k Diedrich head
28ft stroke, 37ft 8" overall
24k pullback 16k pull down
12k 5/8" x 222ft nonrotating winch
4"-13" nominal clamping break out table
Hydrostatic circuit 4500PSI
pilot control
micro feed
float
high/low feed
120gal hydraulic tank
Mounted on a 2004 International 7600 6x4 Truck
Cummins ISM 320V upgraded ECM - rated 385hp
A45/1450 ft torque
Eaton Fuller 13 speed transmission
Hendrickson 38k rear axles
11R22.5 tires
FMC bean pump
3L6 Moyno
Head #A0012 Rebuilt 7/16/10, 9/30/12, 7/23/18 (upgraded roller bearings)
Rebuilt Transmission 8/19/17
Rebuilt winch 8/23/17
Odometer 104,651 miles / 9,374 Hours

Location : USA

Worldrigs ID: WR603
Model : 3000 Drill Rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 3000 Trailer Mounted Drill Rig
Set up for RC
Brewster 18" removable Table
Single draw works
7 Part Main block
2 Cat heads
New Hydraulic pump system
New Hydraulic winch for Tail out
International DT466 Diesel engine
Trailer mounted
6 Leveling jacks
Hydraulic tower ram
Dog House-- Optional at extra cost
The rig is 12’ 6” tall when connected to a day cab tractor. The width is 8’

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR762
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 Range III Drill Rig & Pipe Handling System
Hours 27,319+
Heavy‐duty Derrick and Top head Drive pullback of 120,000 lb
51 ft. 7" in. clearance - plenty of room for 30 ft. drill pipe
8,000 ft‐lb. Spur gear power head
Cummins QSK‐19C Diesel Deck Engine - rated 755‐hp
IR HR2.5 1,250 cfm / 350 psi Air Compressor over/under Air End
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar C13 Diesel Engine - rated 380 HP
Mileage  32,531+
Note: Package Includes:
2014 Foremost Pipe Handler 4000 Series (hydraulic pipe handling system -
hands free) on a 2 axle Trailer
The engine, compressor and hydraulic pumps are mounted on a floating
power‐pack

Location : USA

Worldrigs ID: WR847
Description :

1995 Ingersoll-Rand T4 BH (Blast Hole) Drill Rig
S/N: 4138
Cummins KT19 Diesel Deck Engine - rated 525 horsepower
IR HR2 900 cfm / 350 psi Air Compressor
Spur Gear Power Head with 2 hydraulic motors
37,500 lbs of pullback
7 Rod carousel
Hammer lubricator
Dust collector
100 ft of (4-1/2" x 25ft x 3-1/2"API thread) drill pipe
Air conditioning front and back cabs
Mounted on a 1995 CCC (Crane Carrier)
Cummins M11 Diesel Engine
8LL speed transmission

Note: Cost extra to convert to T4W water well drill rig with repairs.

Location : USA

Worldrigs ID: WR684
Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Moyno water pump
Cummins Diesel deck engine
Detroit 671 T Diesel Engine in truck
140 lb. Safety Hammer
100 ft 6-5/8” augers
rods, bits, etc. included

Location : USA

Worldrigs ID: WR350

Model No : V-2000NG Drill Rig
Manufacturer : Versa Drill
Model Year : 2004
Condition : Used

Description :

2004 Vera Drill V-2000NG Drill Rig
Mounted On A 2003 Kimble Model C3300 6x6 Carrier Truck
Eaton 10 Speed Transmission
5,000 Hours
Fabco 23,000 Lb Front Axle
Spincer 46,000 Lb Rear Axles With Different Lock Out
3-Stage Jake Brake
250 Gallon Aluminum Fuel Tank
Aluminum Wheels
Aluminum Cab
Aluminum Diamond Plate Fenders
Cat C-16 600hp Diesel Engine
Ingersoll-Rand 1070cfm/350psi Air Compressor
80,000lb Pull Back/34,000lb Pull Down
3-Speed Top Head Drive
18,000 Lb Hydraulic Main Winch With Jib
2,000 Lb Auxiliary Winch With Jib
Automated Pipe Storage And Controlsystem
New Batteries
Good Rubber
All Wheel Drive
500' Of 2 7/8 X 4 1/2" Drill Pipe

Location : USA

Worldrigs ID: WR806
Model : 1000 Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing 1000 Water Well Drill Rig
5-1/2" Rotary Table
(2) Leroi Air Compressors (low pressure)
5 X 6 Duplex Mud Pump (with Gardner Denver and Failing Parts installed)
Pipe Rack
Mounted on a 1969 Diamond Rio Truck - VIN #DRE64HC576224
Detroit 8V71 Diesel Engine - rated 318 HP
20 Drill Pipe (2-7/8" OD X 20 x 2-3/8" IF Threads)
(2) Shorter Length Drill Pipe and a Stabilizer

Location : USA

Worldrigs ID: WR854
Description :

Gus Pech 1000R Drill Rig
Set up for Mud Rotary & Auger
Mounted to a 1989 International 1900 Truck
5 speed transmission 2 speed rear
1936+ hours on rig
3 x 4 centrifugal mud pump
3" plumbing to side swivel
450 ft of (4.5″ x 3-2-7/8") drill pipe & holds 225 ft on board the pipe rack
Mud pan attaches to back of rig for transport
Comes with CAT head and auger attachment
3 winches
Jib winch Pullmaster winch 8500 lbs with rapid reverse
wire line for test sampling
2000 lbs sandline
Developmental air compressor
Tophead slides off pole to set pipe
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR840
Description :

Davey Rotary Table Drill Rig
200 PSI Piston Air Compressor
Detroit diesel deck engine
270 gas engine in truck (has a bad valve in it)

Location : USA

Worldrigs ID: WR857
Description :

1973 Gardner Denver 14W Drill Rig
Mounted on a CCC (Crane Carrier Company) Truck
390 ft of Drill Pipe included
Mud Pit & Tee
1000 cfm / 250 psi Air Compressor  
Gardner Denver 5x6 Mud Pump
Bean Water Injection Pump
Cummins 350 Diesel Engine
Foller 13 Speed Transmission
Hour meter reads 1978 Hours
Mileage reads 18,687 Miles
Newer Front tires

Location : USA

Worldrigs ID: WR852
Description :

1989 Schramm T-660 Drill Rig
Detroit 8V92 Diesel Deck Engine (less than 4000 hours since
complete rebuild with preheater)
GHH 900 cfm / 350 psi Air Compressor (Rebuilt, less than 500 hours,
with clutch)
Jib-Boom
Bean water injection pump
360 ft of drill pipe (20ft x 4-1/2"), table bushings & basic tooling included
7 Rod Carousel Lazy Susan
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a GMC White Brigadier Truck (60k+ miles on gauge)
Cat 3208 (Rebuilt transmission less than 2000 miles ago)
Very good tires
Note: Replaced upper chains when the motor were rebuilt about 3500 hours ago

Current repairs needed we are aware of:
Truck CAT 3208 engine starts very hard but once it starts then it runs fine and
runs good (Rebuild time approaching soon)
Traverse cylinders leak small amounts of oil
Deck deck engine leaks small amounts of oil
Compressor clutch work manually only

Location : USA

Worldrigs ID: WR671
Model : C-700 Drill Rig
Manufacturer : Reichdrill
Condition : Used

Description :

Reichdrill C-700 Crawler Drill Rig
Sullair 900 CFM / 375 PSI Air Compressor
Caterpillar 3406 T Diesel Deck Engine
Water Injection Pump
Hammer Lubricator
Drillers Cab
Caterpillar Undercarriage
Metal Tracks

Location : USA

Worldrigs ID: WR83

Model : T64HB
Manufacturer : Schramm
Year : 1972
Condition : used

Description :

1972 Schramm T64HB drill rig
Detroit 8V71 Diesel Deck Engine
425 cfm / 250 psi Air Compressor
Water Injection Pump
Hammer Lubricator
200' ft of Drill Pipe (20' x 4-1/2") and basic tooling included
6" & 8" Hammers & Bits included
Lincoln 225 G7 Welder & Generator on board
Super Rapid Head Travel (loading pipe)
Mounted on a GMC truck
6V53 Diesel Engine
13 Speed Transmission
Flotation Tires (Front), Newer Front Brakes, Newer Transmission

Location : USA

Worldrigs ID: WR787
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger Drill - Unmounted
Year: 1976 / 1977
Dual Motor Hydraulic Top Rotary Power Head (swings away)
11 ft. 6 in. mast (retracted), approximately 18 ft. mast extended
Cathead
Winch
Wisconsin 4 cylindergas motor
In working order
Currently unmounted but comes with trailer it was previously mounted on
included in deal

Location : USA

Worldrigs ID: WR682
Model : CME-75 Drill Rig
Manufacturer : CME Drill
Year : 1988
Condition : Used

Description :

1988 CME-75 Drill Rig
Mounted on a newer 1998 Ford 6X4 FT900 Truck
94,866 miles
3 axles
Ford 300 6 cylinder
Gardner Denver 4.5" x 5" FF FXFM Mud Pump,
2 hydraulic Hoists
wireline & cathead
high torque rotary drive
quick disconnect mast
in-out & sideways slide base
140 lb. auto SPT hammer 
3 hydraulic Jacks
hydraulic Auger rack
500 gallon water tank
three locking tool boxes
locking storage under water tank and rig
Re-diamond plated rig body Feb. 2010 (garage keep since)

Location : USA

Worldrigs ID: WR586

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description :

1994 Ingersoll-Rand T3W
CAT 3406C diesel deck engine (7,000 hours since rebuilt)
IR 825 cfm / 350 psi Air Compressor (4,300 hours since rebuilt)
8,000 lb rotary head
7 rod carousel
rod box
25 GPM Water Injection Pump
Hammer Lubricator
18,000 lb single line winch
Newer Tires
Newer Paint
Mounted on a Ford L9000 Truck
CAT 3176 diesel engine
Eaon 13 speed transmission
9,106 miles on odometer (may be incorrect)
Note: Rig was thoroughly reconditioned by manufacture in 2015 and has only been
used a few hours since

Location : USA

 

Worldrigs ID: WR850
Description :

CME 75 Drill Rig High Torque Fully Refurbished
Refurbished in 2017
Mounted on a 2006 Freightliner M2 truck
Brand new tires and Transmission
Caterpillar engine
Truck has 300,000 actual miles
Brand new hoses
Automatic hammer
Downhole hammer
6 Cylinder Deutz air-cooled engine

Location : USA