Worldrigs ID: WR782
Manufacturer : Speedstar
Condition : As-Is

Description :

Speedstar Quick Drill Rig
Note: only good for Parts
Condition: As-Is
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR860
Description :

Schramm TXD90 Drill Rig
Diesel Deck Engine
Mounted on a Truck

Included as a package :
1,519 feet of 3-1/2" Drill Pipe
6" Collars = 2 Joints (1) 25ft Long (1) 12ft Long
All Subs needed to drill
Elevators

Location : USA

Worldrigs ID: WR537

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig - Serial Number: T64HB-637
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
CAT water injection pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on GMC 6500 truck
Gasoline Engine

Location : USA

Worldrigs ID: WR699
Model : 650 S/S Drill Rig - for Parts or Repairs
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic Model 650 S/S Drill Rig
Condition: As Is - for parts or repairs
Used CP 650 S/S parts machine
Comes with control panel
Hydraulic valves in control panel
CO5 Air Compressor (750 CFM / 125 PSI)
Separator Tank
Rears on CCC Crane Carrier Company truck
Wheels
Oil Tank
Operators Cab
Hydraulic Jacks
Other miscellaneous items as shown in pictures
Note: All Items Sold "As Is"

Location : USA

Worldrigs ID: WR760
Model : H800
Manufacturer : Generic
Condition : Used

Description :

Geospace H800 Drill Rig
Powered by Cummins Diesel Engine
Mounted on International Truck

Location : USA

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR803
Model : 2000 Drill Rig & Package
Manufacturer : Gardner Denver
Year : 1978
Condition : Used

Description :

1978 Gardner Denver 2000 Drill Rig
Mounted on a Truck with 2 axles
Cummins 400 Big Cam Diesel Engine
18" GD rotary table (New Seals)
(2) six line blocks with 120,000 lbs hookload/pullback
Newer cables on kelly and pulling lines
2 cat heads
Hydraulic sand line
With hydro brake set up
Gardner Denver 6x10 mud pump with matco quick change fluid end
New 3" kelly hose high pressure
37 ft square kelly
 
Set up to drill 1600 ft - 2,200 ft water wells
Price Reduced to Sell Fast in July 2020

Included as Package:
1000 ft of 4-1/2" drill pipe
210 ft of 6" drill collars
misc. tooling
pipe truck and trailer

Location : USA

Worldrigs ID: WR807
Model : Larson Reverse Rotary Drill Rig - Air Assited
Manufacturer : Generic
Condition : Used

Description :

1982 Larson Air Assisted Reverse Rotary Drill Rig with Substructure
New derrick 120,000 lbs rated
rebult hydraulic system in 2010
Caterpillar 6 cylinder deck engine (spare rebuilt engine in a crate)
double draw works
1" main line, 1" laydown line, 1/2" tail out line

Included as a Package:
Doghouse - Wired, lighted, AC, tool room, Geolograph
40ft 5th wheel, tandem wheel, drill pipe trailer
Substructure 15ft X 12ft 8ft Custom fabricated with guard rails
1,500  ft of 6-5/8" ID IF modified
90ft of 14" drill collars
2010 Atlas Copco 950 cfm / 350 psi SRVS1000 CD6 Air Compressor
1,000 gallon fuel storage tank with transfer pump
King swivel
Pilot Hole bits
Reaming Hole oppener bits
Casing Collars

Optional Equipment that Cost Extra:
Complete testing pump equipment, 6 pumps, 800 ft of 10x3.5x2.437" column
tube she, gear head, discharge head
12 Cylinder Caterpillar test engine

Location : USA

Worldrigs ID: WR827
Description :

1979 Jaswell 1200 Drill Rig
Mounted on a Paystar 5000 Truck
Detroit 8V92T Diesel Deck Engine (newer clutch)
Sullair 900 cfm / 350 psi Air Compressor (Recent Compressor and Radiator)
New Chains and updated pumps, gear box
Has cat walk
Recent Oil change
Mounted on a Paystar 5000 Truck
Detroit 671 turbo diesel engine
newer rear tires
5 +4 Transmission
All newer paint

Location : USA

Worldrigs ID: WR544

Model: CME-92 Drill Rig
Manufacturer: CME Drill
Condition: Used

Description :

CME-92 Drill Rig
Deck Engine
Mounted on a 5 Ton Chassis Truck
Ford Gas Engine (Model CSG-649P-6006-E)
511,600 km 
3 Hydraulic Leveling Jacks
No Tooling or Hammer will be provided with the unit

Location : USA

Worldrigs ID: WR571

Model : TH75W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1992
Condition : Used

Description:

1992 Ingersoll-Rand TH75W Drill Rig (set up for water well drilling)
Cummins KTA19-C Diesel Deck Engine - S/N 37141244
IR HR2 900 cfm / 350 psi Air Compressor
6 Rod Carousel
Bean Water injection (Head missing)
7221.5+ hours on Meter
est 300' ft of Drill Pipe (20' x 4-1/2") & basic tooling included
4 Hydraulic Leveling Jacks
Mounted on Ford L9000 Truck
VIN# IFDZU90XONVA30165
23,737.8 Miles
CAT 3406 Diesel Engine - rated 400 HP - S/N 3ZJ23533
Good tires
Notes: Compressor cooler has moisture on bottom, Lots of rust on the
under frame,
No major leaks. Complete New Paint Job Cost: $8,500 USD

Location : USA

Worldrigs ID: WR693
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 S/S Drill Rig (2)
No Engine currently on deck (but comes with a rebuilt Caterpillar 3406 diesel
engine (heads need torqued down and fuel line needs put back on)
750 CFM / 125 PSI C05 Air Compressor
Bean (FMC) 4-cylinder water injection pump
Dynex main pump & Dynex Head motor
27,500 lb. pullback capability
Gearmatic Hydraulic winch
4-hole Funk Box (hydraulic pump drive)
3 Hydraulic jacks
4 pieces of 25 ft. drill pipe included
Mounted on 1978 CCC (Crane Carrier Company) truck
Powered by Caterpillar 3208 diesel engine,
showing only 4243 miles on odometer
Deck engine and radiator are included but need re-installed
also comes with spare pull down cylinder

Location : USA

Worldrigs ID: WR788
Model : 30K Drill Rig
Manufacturer : Gefco
Year : 2000
Condition : Used

Description :

2000 Gefco / Speedstar 30K Drill Rig
Top head power drive (has been gone through)
6250+ hours
Mounted on a 2000 Peterbilt 357 Truck
CAT C-15 diesel engine
Sullair 1000 cfm / 350 psi air compressor
Newer Oil Cooler
(12,500+ Hours & 102,250+ Miles on gauge)
30,000 lbs of pullback
Hydraulic Leveling Jacks
Package Includes:
Beals & Welco casing hammer (Casing hammer not in the tower but included)
500 ft of drill pipe, 2 drill collars, and basic tooling

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR872
Description :

PortaDrill 524 Drill Rig
5 Leveling Jacks
7-1/2" Retractable Rotary Table
26ft Kelly
3 Line Machine (Sand Line & Kelly)
2" Little Giant Swivel
Racking Board
Note: No Rod Included

Location : USA

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR797
Model : TXD Drill Rig & Package
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm TXD Drill Rig Package
Deck Engine : Detroit Diesel DDC/MTU 12V-2000

Tilting Top Head Drive : Heavy duty, single reduction gearbox
with 4 two-speed disc valve type hydraulic motors  
variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM  

Feed System : 50 ft (15.24 M) head travel  
200,000 lbf (890 kN) hoist capacity  
100 fpm (30.5 m/min) hoist speed  
32,000 lbf (142 kN) pulldown  
200 fpm (61 m/min) pulldown speed

Drill Table : Table Opening: 30 inches (768 mm) diameter with table retracted  
Hydraulically retractable slip box

Drill Pipe and Casing : Range III tubular capability  
30 inch

Winch : Planetary design with spring applied hydraulic release brake ·
9,600 lbf (42.7 kN) bare drum line pull  
150 fpm (46 m/min) bare drum line speed  
Hydraulic jib boom swing and extend  
Auxiliary winch available

This drill has low wear, Cables and bearing and pivot points,
Control panel all are in excellent condition.
Hoses are getting older.
Mounted on a Trailer
LoadSafe pipe handling systems
Generator house 2 155KW Generators powered by Perkins IR Shop Air,
Hydraulic lift jacks and 3 stage closing unit.
500 HP Mud pump Weatherford T425 powered by John Deere 61356.50 Plunger 900 PSI,
MCM 4x5x14 Super Charge pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House
8000 ft  of drill pipe
4 - 6-1/2” Drill collars
Every pcs is clean and straight nice package.

Location : USA

Worldrigs ID: WR576
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1999
Condition : Used

Description :

1999 Ingersoll-Rand T4W Drill Rig - S/N: 7434
Cummins QSK19 Diesel Deck Engine
IR 1050 cfm / 350 psi Air Compressor
Hammer Oiler
Cat Water Injection Pump
Winches
Mounted on a CCC (Crane Carrier Company) Truck
50,000 lbs of Pullback
2 Motor Spur Gear Power Head
4456+ hours on meter
7X4 Rod Carousels
CAT 3306 Diesel Engine
8741+ Miles on gauge
New Paint Job

Location : USA

Worldrigs ID: WR845
Description :

2001 Foremost DR-24 Drill Rig
Mounted on 2001 Freightliner Truck
Caterpillar C-15 Diesel Engine (rated 500 HP)
4,100 Hours as of 10/16/20
Atlas Copco 900 cfm / 350 psi Air Compressor
24” Diameter Dual Rotary Power Head
Set up for 2-7/8" IF Drill Rod and 6” Beco Rod
4 piston FMC Bean water injection pump
Oil injection system

Package of Tooling :
Jaws 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
Welding (Cage) Clamp 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
Divertor for 4-1/2 inch Drill Rod with adaptors for 6, 8, 10,
12 inch casings
Divertor for 10-3/4 inch drill rod with adaptors for 12, 14, 16, 18,
20, 24 inch casings
Drive Shoes 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
24 - 4-1/2 inch x 20 ft x 2-7/8 IF thread drill rods
6 - 10-3/4 x 20 ft x 6-5/8 Beco thread drill rods
1 – 10-3/4 x 15ft x 6-5/8 Beco thread drill rod
1 - 10-3/4 x 10ft x 6-5/8 Beco thread drill rod
2 – 10-3/4 x 5ft x 6-5/8 Beco thread drill rods
New Miller Welder
Oxy/Acetalene Torch Setup
1 – Petol wrench setup for 4-1/2" Inch drill rod and 6 inch hammer
1 – Petol wrench setup for 6-inch drill rod and 8 inch hammer
6” IR QL60 Drill Hammer with 4-1/2” x 15ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 15ft lead steel with bit
IR QL120 Drill Hammer with 10-3/4" lead steel and subs and
12” bit 12ft - QL120 Bit
2-7/8" IF x 4-1/2" centralizer drill rod for 10" inch casing
24" Inch over the hammer centralizer for QL120 hammer
Cyclone diverter
5 Inch Concrete Discharges Hoses 15 ft
5 Inch Concrete Discharges Hoses 25 ft

Location : USA

Worldrigs ID: WR662
Model : T25K3W Drill Rig
Manufacturer : Driltech
Year : 1994
Condition : Used

Description :

1994 Driltech T25K3W Drill Rig- S/N: 731889
Sullair 840 cfm / 350 psi Air Compressor
CAT 3406 DITA Diesel Deck Engine - rated 430 HP @ 1,800 RPM
30,000 LBS of Pullback
28 ft Head Travel
Pipe Rack Holds For 15 Pipe
(6) Rod Carousel
Rotary Head - rated 89 RPM & 62,600 in LBS. Torque
Jib Boom, Hydraulic Extend With 172 Degree Hydraulic Swing
Hydraulic Winch 7,500 LBS. Capacity
20" Openiing in Table With Hydraulic Adjustment
48" Jaw Type Breakout Wrench
Water Injection Pump is 20 GPM With Foam Pump
DTH Lubricator With 10 Gallon Tank
Fine Feed  & Torque Controls
420 ft. of Used Drill Pipe (4-1/2" O.D. X 20ft) & Basic Tooling Included
Gardner Denver 5 X 6 Air Drive Mud Pump on Board
Hydraulic Leveling Jacks
Mounted on a 1993 Ford LNT8000 - VIN #1FDZW82E0PVA18231
Cummins 8.3l 275 Hp Diesel Engine
10 Speed Transmission
18,000 Front Axle
46,000 Rear Axle

Location : USA

Worldrigs ID: WR562

Description :

Drawworks:
Superior 1000M New (2006) Single Drum Drawworks, 1,000 Hp
Lebus grooved for 1-1/4” Drilling Line, Air operated Makeup
& Breakout Catheads, Over-Running Clutch, Air
Driller’s Console, Crown-O-Matic, Right Angle drive for rotary table.

Compound:
2-Engine, In-Line Compound, w/ Right Angle Drive RT
Box For rotary & Draw works drive

Brake:
PARMAC Dual V-80 Hydromatic Brake coupled together

Drawwworks Power:
No. 1 – CATERPILLAR C-18 Diesel Engine S/N# WJH01728,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N3444
 Air clutch
Hours# 21,597
 No. 2 – CATERPILLAR C-18 Diesel Engine S/N# WJH01706,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N1616
 Air clutch
Hours# 21,664

Mast:
DRILLMASTER New 2008 SN#07632 20’1 1”W x 136’H Cantilever Mast,
With a Gross Nominal Capacity of 930,000 Lbs. and a
650,000 Lb. Static Hook Load, Max wind 91 Knots,
 with ten (10) lines. Crown Block w/ (5)42” Sheave Cluster &
1-56”Fast line Sheave grooved for 1-1/4” diameter drilling line.
Each Crown Sheave wire rope groove is flame hardened.
Each Crown Sheave is fitted with Timken roller bearings and grease seals.
Derrick complete with Crown Safety Platform, 20 finger Racking Board W/ electric mule,
Bridal Lines, Tong Counter Weights, Survey Line Sheaves,
Tugger Sheaves, Ladder, Derrick Climber, Geronimo line,
4” Standpipe & Manifold and
Derrick Stand.
Last Certification 8/23/2012

Substructure:
DRILLMASTER New (2009) 29’10”W x 20’H x 48’8”L
(4) Box-On-Box Substructure w/ Rotary Beams, V-Door Ramp,
Stairs, (2) Air Receiver Tanks, NATIONAL Deadline Anchor,
Safety Rails, inside Catwalk Trolley, 7’W x 14’L built in Tool
Room (ODS) (3) Stairs, Outside wall Winterized, Jacking door,
12’ X 12’ Setback spreader, internal stairway, Vapor proof lighting,
Skidded with oilfield tail rolls

Pump: (Primary)
HT F-1000 Triplex Mud Pump New 2006,
S/N HT 20060088, 1,000Hp.
w/ LANZOU Pulsation Dampener S/N HT20060070,
MF 5,000 Psi. Pressure Gauge 
FIVE STAR 6”x8”x14” Charging Pump S/N5268 p/b TECO 75 Hp. Electric Motor,
 Chinese 3”Shear Relief Value, Master Skidded w/ (2) Engines belt compound

Pump Power:
CATERPILLAR C-18 Diesel Engine S/N WJHO1283,
575 HP w/24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours # 17,376
CATERPILLAR C-18 Diesel Engine S/N WJH01322,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON18CB500 Air Flex Clutch,
 Mounted Pump Master Skid
Hours#16,277

Pump (Secondary)
HT F-1 000 Triplex Mud Pump New 2006,
S/N HT 20060070, 1,000 Hp.
w/ LANZHOU Pulsation Dampener S/N HT20060069,
MF 5,000 Psi. Pressure Gauge
Five Star 6” x 8” x14” Charging Pump S/N5268 p/b Worldwide 75 Hp.
Electric motor,
3” Shear Relief Valve, Master Skidded w/ (2) Engine belt compound

Pump Power
CATERPILLAR C-18 Diesel Engine S/N WJH-00457,
575 HP w/ 24 volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted pump Master Skid.
Hours#13,788
CATERPILLAR C1-8 Diesel Engine S/N WJH-00373,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours#16,643

Rotating Equipment:

Rotary Table
Chinese ZP 27-1/2”, New 2006, complies with API split master bushings,
W/ drive shaft coupling.

Swivel
Ideco 300

Kelly
5-1/4” x 42’ Hex Kelly W/ HDS Kelly Drive Bushing

Kelly Spinner
OWI 1500 Kelly Spinner S/N 00475B w/ (2) Air Motors, New

Kelly Valves
Upper Kelly Valve.
Lower Kelly Valve

Travelling Equipment
Sentry Rig Equipment Company
260 Ton Capacity New 2006
4G260 Traveling Block w/ (5) 36” Sheaves, 1-1/4” Line,
Unitized “Hydra-Hook” 260 Ton Capacity

Blowout Preventer and Valves
1 Each -13-5/8" X 5000# Jiangsu Xianz hong Petroleum 
Double Gate BOP, Top & Bottom Stud configuration
Including - 1set of 5" Pipe Rams Blocks & 1set of Blind Rams,
With 2 - 4" outlets on each side of Body of BOP

1 Each - 13-5/8" Jiangsu Xianz hong Petroleum  ANNULAR BOP
Includes rubber element

1 Each - 13 5/8" X 5000# Type D Drilling Spool W/ - 2" Side Outlet & 3" Side Outlet
[Matched To Choke Manifold

1 Each - Choke Manifold - 3" X 5000# Complete
 Inc - Steel Flex Line W/ Flanges To Connect
To BOPS or Drilling Spools

Closing Unit
2008 Jiangsu Xianz hong Petroleum Model FXQ640-6
Closing Unit Accumulator, 6 Station,
 Rig Floor Controls and monitor panel,
Complete W/ 15 Bottles, 30 HP Cat 3517 Charge Pump, 21 Air Pumps, & set up
for Nitrogen Bottle Backup
Suitcase Closing Unit Skid 7’-1 0” x 35’ with junk basket

Choke Manifold and Valves
Jiangsu Xianz hong Petroleum Choke Manifold w/ (1) 5-Way Cross,
(3) 4-1/16”x 5M
Gate Valves, (4) 2-9/16” x 5M Gate Valves, (1) Manual
Adjustable Chokes, Hydraulic Adjustable Chokes, Mounted Oil Field Skid.
W/ 2 Kill Valves- & 2-Choke Valves mounted at drilling spool

Rig Houses:
Dog House, DRILLMASTER 9’ 1 1”W x 39’ 1 1”L
Doghouse / Change house Combination w/ 17’5”L
Driller’s House w/ Knowledge Box (5) Lockers, Bench Storage, Heater, Lights.
 5’L Breezeway, 1 7’5”L Change House, w/Bench Storage, (16-Lockers,
Cabinets, Heater & Lights. Oil Field Skidded

Generator/Utility Houses
DRILLMASTER 1 1’10”W x 37’9”L x 11’ 6” T
Utility House w/Lights, Oil Field Skidded to include the following items.

No #1 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01986 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0506, complete with Oil Field skid.
Hours# 17,278

No #2 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01985 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0507, complete with Oil Field skid.
Hours# 16,933

NO. 1 GARDNER-DENVER EBE99N New 2006
Electro Saver II Rotary Screw Air Compressor S/N# S237421,
P/b TOSHIBA 30 Hp. Electric Motor, Mounted 240 Gallon Horizontal Tank.
Hours# 15,128

SIEMENS Interlock Panel, 600 Amp 480 Volt Main Lockout Disconnects breakers.

ALLEN BRADLEY Electrical Load center with magnetic starter & breakers,

SQUARE D 225 amp 240 volt panel with breakers

SQUARE D 75KVA Transformer 480 volt to 240 volt

DRILLMASTER 7’9”W x 13”H x 43’1”L Electrical

Suitcase.

DRILLMASTER 2’5”W x 1 3”H x 36’3”L Electrical Suitcases.

Mud System:
DRILLMASTER 9’6”W x 7’H x 34’5”L, 394 Bbl. Suction Tank
10’L Covered Porch, (3) Compartments,
(3) MAX 2000 Mud Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Oil Field Skidded.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
With internal jetting system, 3 dump gates,

DRILLMASTER 9’6”W x 7’H x 34’7”L, 394 Bbl. Shaker Tank
10’L Covered Porch, (3) Compartments
MAX 2000 Mud Agitator Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Skidded.
With internal jetting system, 3 dump gates,

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5269,
p/b BALDOR 75 Hp. Electric Motor.

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5283,
p/b BALDOR 75 Hp. Electric Motor.

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N2450,

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N3089,

NOI DSN-ZH-10CTX Desander S/N 8714-5732,w/ (2) 10” Cones.

NOI DSL-10GG-4CTX Desilter S/N 8714-5731,w/ (10)4” Cones.

DRILCO “Deep Pit” Degasser p/b TECO 10 Hp. Electric Motor

Bubble Buster: Geothermal Type Bubble Buster

Mud House
DRILLMASTER 9’ 1 1”W x 26’L Mud House w/Mud Hopper, Test Sink,
Ventilation Fan, Electric Heater, Lights, Double Side Door, (2) End Doors, Skidded. 
Includes 7’H Tri-Stand on one end the other end sets on suction tank.

Fuel Tank
DRILLMASTER 7’1 1”Wx8’Hx30’L, 13,860 Gallon Fuel Tank
w/ (2) AMT 1/2 Hp. Fuel Transfer Pumps p/b BALDOR 1/2 Hp. Electric Motors,
with Three (3)Compartment, Combo Lubester Oilfield Skidded.

Water Tank
DRILLMASTER 10’10”W x 8’1”H x 35’L, 529 Bbl. Water Tank
w/ 10’L Covered Extension, Pump Room, OilField Skidded
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N 5420, p/b TECO 20 Hp. Electric Motor.
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N5267, p/b TECO 20 Hp. Electric Motor.

Instrumentation
Weight Indicator
Mud Gauges.

Ancillary Equipment
DRILLMASTER 5’W x 2’4”H x 60’L, 2-Section Catwalk w/ Steel Deck and stands for string blocks.
Pipe Racks 5 Sets 29” x 30’ 1 set 29” x 12’ 1 set 41” x 30’
FIVE STAR “Retriever” Electric Measuring Device S/N 862, w/ 15,000 Ft. of. 092 Wire line
2 sets drill pipe elevators 5”
2 sets of drill pipe slips 5”
2 sets of drill collar slips 7” & 9”
2 sets tongs with all head for pipe & casing
2 sets of safety clamps
Mud box  with 5” rubbers
108” X 4” elevator bails
Crossover, bottom hole, lifting Subs
Air Hoist Air Wrench, Model HUL40, S/N-REM10370, 9000 lb. Pull Rating
Air Hoist Air Wrench, Model KSUL, S/N-REM13962, 10,500 lb. Pull Rating
4,000 Ft. of 1-1/4” Drill Line, Mounted Spooler Stand
3-1/2” X 5,000 Psi. Rotary Hose
Vibrator Hose 2 Each 3 ½” x 18’
Rat hole
Mouse hole
8 rig matting boards
Small hand tools & wrenches
Fluorescent & Mercury-Vapor Rig Lights & Wiring Explosion proof
Atco Office/ living shack all electric w/ oil field skid

Worldrigs ID: WR828
Description :

1991 Reichdrill T-650-W Drill Rig
Camion has been repainted
Drill Rig sandblasted
Brakes and boosters has been change
Feed Cylinder redone
Deck engine good
Compressor turns
1300 working hours
Needs some work

Location : North America

Worldrigs ID: WR578

Model : DR12/36 Drill Rig
Manufacturer : Foremost Barber
Year : 1995
Condition : Used

Description

1995 Foremost Barber DR12/36 drill rig
Sullair 1150 CFM / 350 PSI Air Compressor
Cummins KTA19 Diesel Deck Engine (2 Stage) - 600 HP @ 2100 RPM
Cat 12 GPM triplex water injection pump @ 600 psi
Lower Rotary Casing Drive
Opening : 24.7" (627mm)
Stroke : 12' (3 660mm)
Rotation : 0-22rpm
Torque(max) : 1,000,000 lb.in., (113 000Nm)
Hoist Capacity : 72,000 lbs (33,000kg)
combined with top drive  108,000 lb (49,000kg)
Pull Down Capacity : 33,000 lbs (15,000kg)

Top Drive
Stroke : 26' (7 930mm)
Rotation : 0-90 rpm
Torque(max) : 84,000 lbs. in., (9 470Nm)
Hoist Capacity : 37,400 lb.in (17,000kg)
Pull Down Capacity : 16,500lb (7,500kg)
Hoist Speed : 0-64 ft./min (0-20m/min)
Jib Boom / Winch: Pullmaster M5 winch with 120' ft of
wire rope single line pull of 6,000 lbs

Mounted on a Volvo GMC truck
Cummins L10 Diesel Engine at 300 HP @ 2100 RPM
Transmission : Fuller RTX11708LL
10" inch drill pipes (100 meters availiable for an extra cost)

Accessories at an Extra Cost: 
Drill Pipe (4 1/2" x 30' ft) 15 unitsDrill Pipe (30' ft) 18 unitsHammer Bits
(15"-17")Hammer Bit (12")Spindle Adapter (4 1/2" * 1)  and (10" * 1)
Casing Jaw 10" one set , 16" one set and 24" one setDischarge Swivel * 1

Location : South Korea, Asia Region

Worldrigs ID: WR602
Model : 2000 Drill Rig
Manufacturer : Gardner Denver
Year : 1978
Condition : Used

Description :

1978 Gardner Denver 2000 Drill Rig
Trailer Mounted
2 – Detroit 471 turbo diesel deck engine (comes with spare)
Triple drum draw works
57' ft. tubular mast - rated at 100k
100k pullback draw works
18” Howard Turner rotary table
4-½" x 35’ long Kelly bar
Garner Denver 7x10 duplex mud pump
Cathead
Water break
6 line block
5/8" cable on draw works (Kelly and blocks)
1-hydraulic breakout tong (1 backup)
Spinning chain
4-hydraulic leveling jacks
Rack boards set up for 4-1/2” pipe and 8” collars – single height
Air clutches
200 gallon fuel tank
2 cylinder john bean soap injection pump
3” mud piping
2” air piping
Lay down catwalks with handrails

Location : USA

Worldrigs ID: WR178

Model : 1250 Drill Rig
Manufacturer : Failing
Condition : As-Is

Description :

(1) Failing 1250 Drill Rig (being sold for parts)
No Rotary Table
No Mud Pump
No Transfer Case
No Kelly
No Chains
(Basically If You Need A Tower Or Something)
Mounted on a International Truck
Diesel Engine
(1) International 1500 Galloon Water Truck
10 Wheel
Water tank built to bed -O- to haul from pipe beside tank

Location : USA

Worldrigs ID: WR698
Model : B61 Drill Rig
Manufacturer : Mobile
Year : 1989
Condition : Used

Description :

1989 Mobile B61 Drill Rig
Mounted on a 1989 Ford F800 Truck 4x4
429 Gas Engine
Good Tires
Rebuilt transmission
Ford 300 on deck engine
Used daily
200 gal SS water tank
Rod chuck
Wiggle tail
A lot of new parts

Location : USA

Worldrigs ID: WR786
Model : 10R Drill Rig
Manufacturer : Bucyrus Erie
Year : 1972
Condition : Used

Description :

1972 Bucyrus Erie 10R Drill Rig
Started rebuild
Needs back out riggers
No air, or MP
Runs Drives Wont take much to be Drill Ready
Not many hours on this rig for its age

Location : USA

Worldrigs ID: WR759
Model : RD20 Range III Drill Rig
Manufacturer : Atlas Copco
Year : 2012
Condition : Used

Description :

2012 Atlas Copco RD20 Range III Drill Rig Package
Cummins QSC 19C Diesel Deck Engine - rated HP/KW- 755/563 @1800RPM
HHF 500 Triplex Mud Pump with KTA 1150C(19-P750)
CYL.Liner Diameter:6 3/4"(171.5MM) / Length Stroke: 7 1/2" /
Herringbone Tooth, Gear Ratio: 4.286:1
Mounted on a Carrier Truck with 5 axles
Cummins ISM410 Diesel Engine

Package Includes:
Oilwell 214-P 7-1/4X 14 Duplex Mud Pump
Hydraulic Jackup Mud System with ShaleShaker, Mud Cleaner, Agitator,
Hopper, 2 Slurry Pumps
11" 3000 PSI Annular BOP with Accumulator / 7-1/16" 2000 PSI Annular
BOP with acumulator / 9" X 2000 PSI Double Ram BOP
Choke Manifold 3000 PSI 2" Lines
The rig and equipment have been kept in the best possible manner
and are in top shape
Drill Pipe, Drill Collars, Cross Over Subs, Halco Hammers & Bits, spare
rotation head, spare Hydraulic Pumps, spare Rotation motors and lots of
other items included

Location : Asia

Worldrigs ID: WR315

Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New

Description :

Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires

Location : USA

Worldrigs ID: WR372

Model : T650W Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650W Drill Rig
425 CFM / 250 PSI Leroi 256 SD Air Compressor
Diesel Deck Engine
Pipe Rack
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR858
Description :

New & Unused 2012 Atlas Copco RD20 Range III XC Drill Rig
Carrier :
Twin H-beam main frame - reinforced 16 in 406.4 mm
5-axle, custom carrier 415 hp 317 kW diesel engine
8-speed transmission Manual with lo - lo and reverse
Tridem rear axles with lockers 23,000 lb each 10,433 kg each
Tandem front steering axles 22,000 lb each 9,979 kg each

Derrick :
Length 61 ft 11 ½ in 18.88 m
Width 4 48 1/2 in 1.23 m
Depth 41 in 1.04 m
Top of table to spindle 51 ft 6 in 5.7 m
Table to ground (rig sitting on tires) 44 in 1,118 mm
Table to ground (jacks fully extended) 92” 2,337 mm

Rig Dimensions :
Height derrick down 13 ft 10 in 4.22 m
Height derrick up 62 ft 6 in 19.05 m
Width 8 ft 4 in 2.54 m
Shipping weight (less tooling) 88,000 lb 40,000 kg

Tip Out Links :
Forged steel 150 ton 136 tonnes
Length 60 in 1,524 mm
Tip out hydraulic cylinder on each link
Angle 0-80° from vertical
Control drillers console

Table & Master Bushing :
Design folding with twin hydraulic jacks
Max opening 26 in 660 mm
API split master bushing 17 ½ in 445 mm
Capacity 60 ton 54.4 tonnes

Rig Performance :
Hookload 120,000 lb 54.4 tonnes
Pulldown 30,000 lbf 13,636 kg
Fast feed up 106 ft/min 32.3 m/min
Fast feed down 180 ft/min 54.9 m/min
Drill feed 29 ft/min 8.8 m/min
Torque 8,000 lbf-ft 10.8 kNm
Speed 0-120 RPM 0-120 RPM
Spindle 3 in 76.2 mm
Swivel Type Multi chevron packings
Opening 2 ½ in 63.5 mm

Location : USA

Worldrigs ID: WR797
Model : TXD Drill Rig & Package
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm TXD Drill Rig Package
Deck Engine : Detroit Diesel DDC/MTU 12V-2000

Tilting Top Head Drive : Heavy duty, single reduction gearbox
with 4 two-speed disc valve type hydraulic motors  
variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM  

Feed System : 50 ft (15.24 M) head travel  
200,000 lbf (890 kN) hoist capacity  
100 fpm (30.5 m/min) hoist speed  
32,000 lbf (142 kN) pulldown  
200 fpm (61 m/min) pulldown speed

Drill Table : Table Opening: 30 inches (768 mm) diameter with table retracted  
Hydraulically retractable slip box

Drill Pipe and Casing : Range III tubular capability  
30 inch

Winch : Planetary design with spring applied hydraulic release brake ·
9,600 lbf (42.7 kN) bare drum line pull  
150 fpm (46 m/min) bare drum line speed  
Hydraulic jib boom swing and extend  
Auxiliary winch available

This drill has low wear, Cables and bearing and pivot points,
Control panel all are in excellent condition.
Hoses are getting older.
Mounted on a Trailer
LoadSafe pipe handling systems
Generator house 2 155KW Generators powered by Perkins IR Shop Air,
Hydraulic lift jacks and 3 stage closing unit.
500 HP Mud pump Weatherford T425 powered by John Deere 61356.50 Plunger 900 PSI,
MCM 4x5x14 Super Charge pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House
8000 ft  of drill pipe
4 - 6-1/2” Drill collars
Every pcs is clean and straight nice package.

Location : USA

Worldrigs ID: WR691
Model : 1500 drill rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 1500 drill rig
5x6 mud pump
kelly drive recentlly rebuilt
Mounted on a twin axle carrier
Diesel engine
Note: no air compressor on board

Location : USA

Worldrigs ID: WR880
Description :

1984 Speedstar Quickdrill 600 Drill Rig
Mounted on an International 2574 Truck
Rebuilt - Detroit 8V92 Deisel Engine with Jake brakes
Rebuilt - Eaton Fuller 13 speed transmission with new clutch-throw out bearing
All new coolant-oil hoses, radiator, exhaust from turbo to muffler, drive shafts, &
rear end
Feed-outrigger-jib-rod jaw-tower hydraulic cylinders and hoses all new
Fully rebuilt top head - gears, bearings, seals, hydraulic motors, north Houston
machine under head mud and air swivel all new. New high pressure airline and
fittings from compressor to top head.
10 GPM water injection pump - completely rebuilt
12,000 lb main winch fully rebuilt including all bearings, seals, and hydraulic motor.
Rebuilt rod box
New oil filters on compressor
600 cfm / 250 air compressor
500 ft 3-1/2” OD by 2-3/8 IF drill rods
table bushings, etc.
Drive traction tires 60% percent & Steer tires 80% percent estimated

Location : USA

Worldrigs ID: WR770
Model : GP-900XHR Drill Rig
Manufacturer : Gus Pech
Year : 2007
Condition : Used

Description :

2007 Gus Pech Drill Rig
GP-900XHR
10,000+ Hours on Sterling Truck & 8,000+ Hours Drill
Overhauled at Gus Pech Factory in 2017
Sullair 700 cfm / 200 psi Air Compressor
7x10 Centerline Mud Pump
Standard Power Head
450 hp Mercedes Diesel Engine
Set up for Minerial Exploration
estimated rig weighs 48660 lbs, 8ft 6” W, 13ft H, 37ft L

Location : North America

Worldrigs ID: WR83

Model : T64HB
Manufacturer : Schramm
Year : 1972
Condition : used

Description :

1972 Schramm T64HB drill rig
Detroit 8V71 Diesel Deck Engine
425 cfm / 250 psi Air Compressor
Water Injection Pump
Hammer Lubricator
200' ft of Drill Pipe (20' x 4-1/2") and basic tooling included
6" & 8" Hammers & Bits included
Lincoln 225 G7 Welder & Generator on board
Super Rapid Head Travel (loading pipe)
Mounted on a GMC truck
6V53 Diesel Engine
13 Speed Transmission
Flotation Tires (Front), Newer Front Brakes, Newer Transmission

Location : USA

Worldrigs ID: WR560

Model : T130 Drill Rig
Manufacturer : Schramm
Model Year : 2003
Condition : Used

Description

2003 Schramm T130 Drill Rig - S/N: J130-0707
Detroit DDC/MTU V12-2000TA DDEC Diesel Deck Engine
Mast: Telescoping construction permits long head travel 50’' ft
Note: Shorter length in transport position
130,000 lbs of Pullback
Free standing design with 28"” table opening
Sullair 1350 cfm / 350 psi Air Compressor (Rebuilt with low hours)
Hydraulic pumps (low hours since rebuilt)
Top Head: Fixed position - two hydraulic motors. 0-143 RPM with 106,600 in-lb of torque
Pipe handling sling
Set up for RD20 style (4-½”" X 30'’ X 2-7/8" IF) Drill Pipe
Carousel
Cat Water Injection Pump
Graco Hammer Lubricator
Mounted on a CCC (Crane Carrier Company) Truck - VIN#: 1CYDGD5843T046189
CAT diesel engine
425/65R22.5 front tires 12R22.5 rear tires
Sub Base: 9'’ wide 40'’ long and 3’' tall & Basic Tooling Included

Location : USA

Worldrigs ID: WR766
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger / Rotary Drill Rig
Combo auger/rotary
Mounted on 2000 Chevy W4500
Duetz diesel deck engine
25 HP kohler mud pump engine
Mud pump is a 2X3 centrifugal
170 feet of drill rod with 2 roller cone bits
Drill rod is 2-7/8 OD
10 ft extension to the derrick that allows you to work with 20 ft
lengths of pipe
Break out wrench and air compressor on the truck
Truck is a 5 speed cab over
Truck has 135239k and is 2 wheel drive 4 cyl Isuzu diesel
IMT HYD 25CFM @100PSI Air Compressor (?)
Simco thread and set up to run 10 foot lengths

Location : USA

Worldrigs ID: WR539

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig - Serial Number: T64HB-1313
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on a GMC truck - VIN TJV738V578079
diesel engine

Location : USA

Worldrigs ID: WR762
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 Range III Drill Rig & Pipe Handling System
Hours 27,319+
Heavy‐duty Derrick and Top head Drive pullback of 120,000 lb
51 ft. 7" in. clearance - plenty of room for 30 ft. drill pipe
8,000 ft‐lb. Spur gear power head
Cummins QSK‐19C Diesel Deck Engine - rated 755‐hp
IR HR2.5 1,250 cfm / 350 psi Air Compressor over/under Air End
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar C13 Diesel Engine - rated 380 HP
Mileage  32,531+
Note: Package Includes:
2014 Foremost Pipe Handler 4000 Series (hydraulic pipe handling system -
hands free) on a 2 axle Trailer
The engine, compressor and hydraulic pumps are mounted on a floating
power‐pack

Location : USA

Worldrigs ID: WR761
Model : T500XD Drill Rig
Manufacturer : Schramm
Year : 2013
Condition : Used

Description :

2013 Schramm T500XD Drill Rig
1,500 HP Drilling Rig
Fluid Pressure Rating: 7,500 psi

Power Unit :
MTU 12V -2000 engines, 760 bhp (567 kw) @ 1,800 rpm with electric start
Dual core, side by cooling package, 130”F ambient rating
220 gallon diesel fuel tanks
Hydraulic pump systems, with each including (8) piston pump systems
and (1) gear type pump
(1) 1,000 gallon hydraulic tank with (18) twin element hydraulic tank
with (18) twin element hydraulic tank with (18) twin element hydraulic
tank with (18) twin element hydraulic tank with (18) twin element filters

Sub -Base and Walking System :
Floor Height : 22 ft.
Clearance : 19 ft. under table bushing

Telemast System :
Top Head Travel: 56 ft.
Hook Load : 500,000 lbs. actual Hoist
80,000 lbs pulldown capacity

Tilting Top Drive :
Rotation Speed: 0-140 RPM
Rotation Torque: Up to 35,000 ft-lbs

Rig Floor :
37.5 inch false table adapter and a 27.5 inch Master Bushing

Hydraulic Roughneck :
Make/Break Torque: 60,000 ft -lbs @ 3,500 psi
Loadsafe XD Pipe Handling System

Mud Pumps :
(2) Gardner Denver PZ-11HP 1,000 HP / 7,500 PSI

Power :
One, Detroit diesel 16V2000P EPA Tier 1 One

Standard Accessories :
Water injection system, rated 35 gpm @ 1,000 psi
DTH lubricator rated up to 5 gph (19 lph ) @ 1,000 psi ) @ 1,000 psi
Air manifold for air drilling operations
Air/mud fluid lines, 4 inch stand pipe and traveling hose for
7,500 psi operation
Explosion proof 240V lighting for nighttime operation
(customer supplied generators) BOP handling system,
carriage and trolley rated 40,000 lbs.
Support Equipment :
40ft Conex BoX : with spare parts for Rig

Trip Tank :
Fabricated skid mounted tank with (40 bbl. of capacity) 4 x 3 centrifugal pump

Mud Pits :
Two tanks – shaker tank and suction (750 bbls). Shakers – Vortex triple
shakers w/5 agitators.
Mud hopper.Class 1 Div 1 lighting

Location : USA

Worldrigs ID: WR757
Model : T500XD Telemast Drill Rig - Trailer Mounted
Manufacturer : Schramm
Condition : New

Description :

New 2015 Schramm T500XD Telemast Drill Rig
Trailer Mounted
Rated 1520 HP Diesel Power
60° PAD Walking System
Tilting Top Drive
Control Room
Loadsafe® XD Automated Pipe Handling System
Hands Free Power Breakout
500,000 lbs. (226,796 kg) hook load rig in a portable over the road package
80,000 lbf. (356 kN) hydraulic pulldown for precise weight on bit control
Control cabin with joystick controllers for drilling and pipe handling
operations Self-erecting in a matter of hours without the use of a crane
Power breakout, table and slips maximize safety on the drill floor
LoadSafe XD hands-free Range III pipe handling system included
Crew of three typical
Optional dual fuel configuration available
no draw works on this rig, has hyd powered hoist and rotation

Note: Major Price Reduction to Sell Quickly

Expected fuel consumption per hour?
Model: MTU 12V-2000TA DDEC Tier 1
Power: 760 bhp (567 kw) @ 1,800 rpm
Torque: 2,188 ft-lb (2,967 N-m) @ 1,800 rpm
Displacement: 1,458 cu. in. (23.9 l)
B.S.F.C.: .338 lb/bhp-hr @ Maximum Power (206 g/kw-hr)
Fuel Consumption: 36.2 g/hr @ Maximum Power, 27 g/hr @ Average Load
Horsepower Ratings: +2%, -0%
Altitude Performance, All MTU Series 2000 Engines - % of Rated BHP:
5,000ft (1524m) = 99.0% at 1800 rpm
10,000ft (3048m) = 97.0% at 1800 rpm
15,000ft (4572m) = 94.5% at 1800 rpm

Location : USA

Worldrigs ID: WR770
Model : GP-900XHR Drill Rig
Manufacturer : Gus Pech
Year : 2007
Condition : Used

Description :

2007 Gus Pech Drill Rig
GP-900XHR
10,000+ Hours on Sterling Truck & 8,000+ Hours Drill
Overhauled at Gus Pech Factory in 2017
Sullair 700 cfm / 200 psi Air Compressor
7x10 Centerline Mud Pump
Standard Power Head
450 hp Mercedes Diesel Engine
Set up for Minerial Exploration
estimated rig weighs 48660 lbs, 8ft 6” W, 13ft H, 37ft L

Location : North America

Worldrigs ID: WR774
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1995
Condition : Used

Description :

1995 Ingersoll-Rand T4W Drill Rig
IR 1000 cfm / 350 psi Air Compressor - (14,000 hours)
Cummins QSK Diesel Deck Engine - rated 600 HP & 2100 RPM - (Reman
as of March 2016 with 1,971 hours on meter as of 8-6-2019)
50,000 lbs of pullback
Worm Gear Power Head
Water Injection Pump
Hammer Lubricator
7 & 4 Rod Carousel
Starting Aid Diesel Fired Pre-heater with Ether
Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar 3306 C diesel engine
mileage 75,000

Location : USA

Worldrigs ID: WR799
Model : T4W LT Range II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2005
Condition : Used

Description :

Ingersoll-Rand T4W LT (Long Tower) Range II Drill Rig
2005 CAT C-12 Diesel Engine (4,000 hours)
Ingersoll-Rand 1170 cfm / 350 psi Air Compressor
70,000 lbs of Pullback (Deep Hole)
4 hole gearbox and 2 hole gearbox
High Torque Spur Gear power head with cushion sub
Bean Water Injector Pump rated at 2000 psi
Mounted on a CCC (Craine Carrier Company)
CAT 3406 Diesel Engine
2400 Gal Fuel Tank with Hose Reels
12V Electric Pump

Mounted on a 32 ft Tandum Axle trailer
Sullair 1150 cfm / 350 psi Air Compressor
CAT C-15 Diesel Engine with 7,000 hours

Hurricane Booster - rated 900 lbs of pressure
CAT 3126 Diesel Engine
Both mounted on a 32' ft Tandum Axle Trailer

120 Pipe of T4 style drill pipe (3,000 ft) 3-1/2" Reg Pin and Box
5 check valve subadapters
Pipe and adapters are all loaded on 2 tandum axle flat bed trailers
Drill Rig Base or Platform
14" tall 35 ft long 10 ft wide with folding ramps and fold down walkways
38 ft tandum axle trailer with roller for moving
IR-120 Hammer with 12-1/4" bit x 11" x 20 Stabilizer
IR-TD-90 Hammer with 8-7/8" bit x 8" x 20 Stabilizer
IR QLX-60 Hammer w/ 6-1/4"bit, 6" by 25ft Stabilizer
3 sets of Casing Clamp type Elevators for 4-1/2", 7" & 9-5/8"
Washington rotation head diverter assembly with adaptter plates
35 ft of blow pipe with hammer unions
2 complete Petol wrenches, Misc Table bushings & Wrenches Forks and Subs

Location : USA

Worldrigs ID: WR886
Description :

2012 Schramm TXD 200 Drill Rig
serial number J135-0216, trailer VIN#: 1K9AD40C1C3268138.
Detroit DDC/MTU 12V-2000 Diesel Deck Engine

Tilt Top Head Drive:
Heavy duty, single reduction gearbox with 4 two-speed disc valve type 
hydraulic motors
Variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM · 

Feed System:
50 ft (15.24 M) head travel
200,000 lbf (890 kN) hoist capacity
100 fpm (30.5 m/min) hoist speed
32,000 lbf (142 kN) pulldown
200 fpm (61 m/min) pulldown speed

Drill Table:
Table Opening : 30" inches (768 mm) diameter with table retracted
Hydraulically retractable slip box

Drill Pipe And Casing:
Range III tubular 30 inch capability

Winch:
Planetary design with spring applied hydraulic release brake
9,600 lbf (42.7 kN) bare drum line pull
150 fpm (46 m/min) bare drum line speed
Hydraulic jib boom swing and extend
Auxiliary winch available
The drills have low wear on the cables, bearing and pivot points as well 
as the Control panel
All are in excellent/very good condition during last inspection
LoadSafe pipe handling systems (hands free pipe loading system)
mounted on Trailers

Package available  each of the following:
Generator House with 2 Maraathon Model 431CSL6202-B211 60 HZ Phase 1 
120/240V 122 KW 504 AMO or 3 Phase 277/480 155 KW 233 AMP poered by 
Perkins 6.6 L 1106 IR 2340 Shop air ,Hyd lift with Honda GX392,4000 Gallon 
feul tank and 4 lights on roof.
Weatherford T425 Triplex Mud pump powered by John Deere 6135 diesel engine 
(Tier IV) - rated 500 HP, 6.50 Plunger 900 PSI, MCM 4x5x14 Super Charge 
Centrifugal pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House 
8000 ft of drill pipe (4" DP New 30ft 6" NC40)
(4) 6-1/2” Drill collars
Every unit is clean & straight and it is a very nice package in excellent/very 
good condition after inspections in 2020

Location : USA

Worldrigs ID: WR863
Description :

1977 Chicago-Pneumatic 7000 Top Head Drive Rotary Drill Rig - S/N: 97328
Cat 3406-A diesel deck engine
GHH 825-300 air compressor
43 ft hydraulic raise mast
7" diameter 70,000 lbs hydraulic pull back and pull down hydraulic cylinders
8,000 lbs hydraulic winch and hydraulic jib
hydraulic break-out wrench
carousel
table bushings
fold up rear platform
3-hydraulic outriggers
120-volt work lights
Mounted on a 1975 Mack DM600 Truck tandem axle chassis - VIN# DM492S1239
Mack 300 diesel engine
Mack 6 speed lo-hole transmission
equipped with Jacobs engine brake
Mack camelback spring suspension
216" wheelbase
445/65 22.5 front and 11.00-20 rear tires
In fair to good condition
Upper Meter Reads 4,441 Hours & Odometer Reads 60,157 Miles

Location : USA

Worldrigs ID: WR661
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 - Range III Drill Rig
120,000 lbs of pullback
Cummins QSK19 Diesel Deck Engine (Very Low Hours)
IR HR2.5 1250 cfm / 350 psi Air Compressor with In/Out box
Rotary Head: 4SV-2-10 Spur gear
Top drive head assembly rated to 8,000 ft. lbs. torque
Single Rod Loader for handling 4.5” o.d. X 30ft long drill rods
Spindle Sub – (4 1/2” x 2 7/8IF")
Water Injection Pump
Hammer Lubricator
Mounted on a CCC (Crane Carrier Carrier) Truck
CAT C13 Diesel Engine

Tooling & Pipe included:
51 (4-1/2 X 30ft X 2-7/8IF") Thread Drill Pipe
12 - (6” X 30ft) Slick Drill Collars
3 - (8” X 30ft) Spiral Drill Collars
Basic Tooling
23 Subs on Steel Platform on Pins

Location : USA

Worldrigs ID: WR789
Model : TLS Drill Rig
Manufacturer : PortaDrill
Year : 1978
Condition : Used

Description :

1978 PortaDrill TLS Drill Rig
Rebuilt - Volvo Diesel Deck Engine - rated 500 HP
500 ft. of 3-1/2" inch Drill Pipe included
Pipe Rack
Top head was rebuilt in summer 2018
New Water Injection Pump installed in summer 2018
Mounted on a Truck
Cummins diesel engine

Location : USA

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR682
Model : CME-75 Drill Rig
Manufacturer : CME Drill
Year : 1988
Condition : Used

Description :

1988 CME-75 Drill Rig
Mounted on a newer 1998 Ford 6X4 FT900 Truck
94,866 miles
3 axles
Ford 300 6 cylinder
Gardner Denver 4.5" x 5" FF FXFM Mud Pump,
2 hydraulic Hoists
wireline & cathead
high torque rotary drive
quick disconnect mast
in-out & sideways slide base
140 lb. auto SPT hammer 
3 hydraulic Jacks
hydraulic Auger rack
500 gallon water tank
three locking tool boxes
locking storage under water tank and rig
Re-diamond plated rig body Feb. 2010 (garage keep since)

Location : USA

Worldrigs ID: WR846
Description :

2013 Schramm TXD Drill Rig
API Certified Rig
23,635 Hours
Mounted on a Trailer

Items Available for Additional Cost:
Loadsafe System and Pad
Drill Pipe
Collars
Handeling Tools
Doghouse
Air Compressors
Mud Pumps
Pits
Shakers

Location : USA

Worldrigs ID: WR860
Description :

Schramm TXD90 Drill Rig
Diesel Deck Engine
Mounted on a Truck

Included as a package :
1,519 feet of 3-1/2" Drill Pipe
6" Collars = 2 Joints (1) 25ft Long (1) 12ft Long
All Subs needed to drill
Elevators

Location : USA

Worldrigs ID: WR571

Model : TH75W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1992
Condition : Used

Description:

1992 Ingersoll-Rand TH75W Drill Rig (set up for water well drilling)
Cummins KTA19-C Diesel Deck Engine - S/N 37141244
IR HR2 900 cfm / 350 psi Air Compressor
6 Rod Carousel
Bean Water injection (Head missing)
7221.5+ hours on Meter
est 300' ft of Drill Pipe (20' x 4-1/2") & basic tooling included
4 Hydraulic Leveling Jacks
Mounted on Ford L9000 Truck
VIN# IFDZU90XONVA30165
23,737.8 Miles
CAT 3406 Diesel Engine - rated 400 HP - S/N 3ZJ23533
Good tires
Notes: Compressor cooler has moisture on bottom, Lots of rust on the
under frame,
No major leaks. Complete New Paint Job Cost: $8,500 USD

Location : USA