Worldrigs ID: WR798
Model : CM-780D Blasthole
Manufacturer : Ingersoll-Rand
Year : 2003
Condition : Used

Description :

2003 Ingersoll-Rand CM-780D Blasthole Drill Rig
Crawler Mounted
Caterpillar Diesel Engine
S/N: G78255EL
IR HR2 865 CFM / 350 PSI Air Compressor
Water injection
Hammer Lubricator
Thread Greaser
Enclosed Cab
A/C & Heater
Rod Changer
13-1/2" Track Shoes
Set up for (3-1/2”O.D. x 13.1ft) Drill Pipe 21/2Z thread
Meter Reads 15,940 Hours

Location : USA

Worldrigs ID: WR858
Description :

New & Unused 2012 Atlas Copco RD20 Range III XC Drill Rig
Carrier :
Twin H-beam main frame - reinforced 16 in 406.4 mm
5-axle, custom carrier 415 hp 317 kW diesel engine
8-speed transmission Manual with lo - lo and reverse
Tridem rear axles with lockers 23,000 lb each 10,433 kg each
Tandem front steering axles 22,000 lb each 9,979 kg each

Derrick :
Length 61 ft 11 ½ in 18.88 m
Width 4 48 1/2 in 1.23 m
Depth 41 in 1.04 m
Top of table to spindle 51 ft 6 in 5.7 m
Table to ground (rig sitting on tires) 44 in 1,118 mm
Table to ground (jacks fully extended) 92” 2,337 mm

Rig Dimensions :
Height derrick down 13 ft 10 in 4.22 m
Height derrick up 62 ft 6 in 19.05 m
Width 8 ft 4 in 2.54 m
Shipping weight (less tooling) 88,000 lb 40,000 kg

Tip Out Links :
Forged steel 150 ton 136 tonnes
Length 60 in 1,524 mm
Tip out hydraulic cylinder on each link
Angle 0-80° from vertical
Control drillers console

Table & Master Bushing :
Design folding with twin hydraulic jacks
Max opening 26 in 660 mm
API split master bushing 17 ½ in 445 mm
Capacity 60 ton 54.4 tonnes

Rig Performance :
Hookload 120,000 lb 54.4 tonnes
Pulldown 30,000 lbf 13,636 kg
Fast feed up 106 ft/min 32.3 m/min
Fast feed down 180 ft/min 54.9 m/min
Drill feed 29 ft/min 8.8 m/min
Torque 8,000 lbf-ft 10.8 kNm
Speed 0-120 RPM 0-120 RPM
Spindle 3 in 76.2 mm
Swivel Type Multi chevron packings
Opening 2 ½ in 63.5 mm

Location : USA

Worldrigs ID: WR874
Description :

Gardener Denver 15W Drill Rig
Rebuilt and Painted
Truck engine has been rebuilt
Mud pump has also been rebuilt
10” Gardner Denver Retractable table
58ft Mast
Racking board
Bailing drum
new 2” little giant swivel
new 26ft Kelly
hydraulic pull down
air clutches
4 hydraulic leveling jacks

Location : USA

Worldrigs ID: WR707
Model : 275 Drill Rig
Manufacturer : Speedstar
Year : 1989
Condition : Used

Description :

1989 Speedstar 275 Drill Rig
PTO drive
The rig runs 20ft rods
Holds 340ft of 2-7/8 Mayhew Regular in the rack
600ft of fairly new rods included
Note: No rod loader, no carousel, no hammer oilier, no bean pump
The rig currently has a non-operational joy twist air
Mounted on a 1988 International truck - All Wheel Drive
Sandline possibly its a 2500lb
Has a new Braden 12k main winch from Gefco
5x6 Gardner Denver Mud pump - Completely rebuilt including all components
in the gear end & shafts.
New Hubcity 3h gearbox to drive mud pump from Gefco
Both top head motors are new (originals as a backup)
Top head has been completely rebuilt (New spindle shaft and components
from Gefco)
New paint job with Emron aircraft paint. Truck was completely sandblasted and
taken down to bare metal and brought back to its current condition. (Pictures
available documenting the work).
It is a Speedstar 275 which is almost identical to the quickdrill 275 but it
is a newer version and has some features that the quickdrills dont have.

Location : USA

Worldrigs ID: WR216

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description :

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR853
Description :

Canterra CT-350 Drill Rig
Mounted on a 1989 Ford Truck
5-speed transmission with 2-speed rear
Diesel engine
Rod rack and plumbing for rotary option
Brand new hydraulic system installed in early 2019
(only 6 wells drilled in since)
Main line and sand line with free fall and spudder option
We would drive the wells in with a spudder option
Auger rack on the drivers side
Rod rack and tool box on the passenger side
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR456

Worldrigs ID: WR596
Model : D40K Drill Rig
Manufacturer : Driltech
Year : 1974
Condition : Used

Description :

1974 Driltech D40K Drill Rig
CAT Diesel Deck Engine - rated 425 HP
Sullair 750 cfm / 150 psi air compressor
25’ ft inner & outer Carousels
8000 lb main/jib
Gardner Denver 5x6” Duplex Mud pump (variable hydraulics)
20 GPM water injection pump
Rebuilt hydraulic pumps & splitter
Hot box
good tires
Mounted on a CCC (Crane Carrier Company) Truck
466 diesel engine
Extra: 275’ ft of (25’ x 4-1/2” x 2-7/8 IF Rods)
23’ ft surface collar & mud pit

Location : USA

Worldrigs ID: WR690
Model : T130XD Drill Rig
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm Rotadrill T130XD Drill Rig
Fluid Line Plumbing, Welded
Rotation Guard
Telemast 50 ft
Helpers Platform, Mast Mounted
Mini Lube System
Pullback Limiter
Rotationlock for DH Mtr, w/FS
Slow Feed Drill-Up Valve
Tophead High Cap 4 Meter 4" Tilt
Four Meters, 15/30 cu in
Split Table Assembly, No Slips
Adj Height Brkout Wrnch Mount
Variable Spd Fan (No Comp)
Heater, Diesel Fired Coolant
Spark Arrestor
Note: No Air Compressor on board
Auxiliary Tooling Compressor
Tool Lubricator, Piston Pump
Mounted on a CCC (Crane Carrier) Truck 10x6 ULSD
Aluminum Wheels 10
Heater, Diesel Fired Coolant
ProHeat style Heater for Crane Carrier motor
Pro Heat# PH0403
Jib Boom, Hydraulic Range 2
Hydraulic Pipe Racks, Set (2)
LoadSafe Handler Hydraulic Supply
LoadSafe Pipe Handler
Power Breakout
Remote Hydraulics Supply
Winch, 9,600 lb (150 ft x 1 /2")
Winch, Survey Line

Location : Western Region

Worldrigs ID: WR315

Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New

Description :

Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires

Location : USA

Worldrigs ID: WR776
Model : SDC500-29P Drill Rig
Manufacturer : Sonic
Condition : Used

Description :

Sonic SDC500-29P Drill Rig
80k Diedrich head
28ft stroke, 37ft 8" overall
24k pullback 16k pull down
12k 5/8" x 222ft nonrotating winch
4"-13" nominal clamping break out table
Hydrostatic circuit 4500PSI
pilot control
micro feed
float
high/low feed
120gal hydraulic tank
Mounted on a 2004 International 7600 6x4 Truck
Cummins ISM 320V upgraded ECM - rated 385hp
A45/1450 ft torque
Eaton Fuller 13 speed transmission
Hendrickson 38k rear axles
11R22.5 tires
FMC bean pump
3L6 Moyno
Head #A0012 Rebuilt 7/16/10, 9/30/12, 7/23/18 (upgraded roller bearings)
Rebuilt Transmission 8/19/17
Rebuilt winch 8/23/17
Odometer 104,651 miles / 9,374 Hours

Location : USA

Worldrigs ID: WR756
Model : V-1040DP Drill Rig
Manufacturer : Versa Drill
Year : 2010
Condition : Used

Description :

2010 Versa Drill V-1040DP Drill Rig
Caterpillar C15 Diesel Engine (Tier III - S/N: JRE11211) - rated
540 HP & 2100 RPM
IR 1070 cfm / 350 psi Air compressor (Clutch)
6500+ Hours on gauge
40,000 lbs of pullback
Hammer Lubricator 7 Gallon
Bean 4 piston bean water injection 25 GPM
Main Winch 18k & Secondary 2k
Pipe rack holds 18 pipe
4 stabilizing Jack
Mounted on a 2010 Peterbilt 367 Truck
Cummins ISX 15 Diesel Engine (Tier III - S/N: 1040039) - rated
565 HP (Heater) with 31,000+ Miles on gauge
Eaton Fuller 13 Speed LL Transmission
Jake Brakes
22,000 lb. front axle, 46,000 lb. rear tandem axles with driver
controlled main locking differentials, total 68,000 GVW
Total Weight 55,520 lbs = Front Axle: 15,620 lbs &
Rear Axle: 39,560 lbs

Location : USA

Worldrigs ID: WR831
Description :

1996 Speedstar SD300 Drill Rig
Mounted on an 1995 International Truck
Cummins N14 Diesel Engine
10 Speed transmission
Sullair 750 cfm / 350 psi air compressor with clutch
Gardner Denver 5x6 Duplex Mud Pump (hydraulic driven)
Pipe rack
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR846
Description :

2013 Schramm TXD Drill Rig
API Certified Rig
23,635 Hours
Mounted on a Trailer

Items Available for Additional Cost:
Loadsafe System and Pad
Drill Pipe
Collars
Handeling Tools
Doghouse
Air Compressors
Mud Pumps
Pits
Shakers

Location : USA

Worldrigs ID: WR562

Description :

Drawworks:
Superior 1000M New (2006) Single Drum Drawworks, 1,000 Hp
Lebus grooved for 1-1/4” Drilling Line, Air operated Makeup
& Breakout Catheads, Over-Running Clutch, Air
Driller’s Console, Crown-O-Matic, Right Angle drive for rotary table.

Compound:
2-Engine, In-Line Compound, w/ Right Angle Drive RT
Box For rotary & Draw works drive

Brake:
PARMAC Dual V-80 Hydromatic Brake coupled together

Drawwworks Power:
No. 1 – CATERPILLAR C-18 Diesel Engine S/N# WJH01728,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N3444
 Air clutch
Hours# 21,597
 No. 2 – CATERPILLAR C-18 Diesel Engine S/N# WJH01706,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N1616
 Air clutch
Hours# 21,664

Mast:
DRILLMASTER New 2008 SN#07632 20’1 1”W x 136’H Cantilever Mast,
With a Gross Nominal Capacity of 930,000 Lbs. and a
650,000 Lb. Static Hook Load, Max wind 91 Knots,
 with ten (10) lines. Crown Block w/ (5)42” Sheave Cluster &
1-56”Fast line Sheave grooved for 1-1/4” diameter drilling line.
Each Crown Sheave wire rope groove is flame hardened.
Each Crown Sheave is fitted with Timken roller bearings and grease seals.
Derrick complete with Crown Safety Platform, 20 finger Racking Board W/ electric mule,
Bridal Lines, Tong Counter Weights, Survey Line Sheaves,
Tugger Sheaves, Ladder, Derrick Climber, Geronimo line,
4” Standpipe & Manifold and
Derrick Stand.
Last Certification 8/23/2012

Substructure:
DRILLMASTER New (2009) 29’10”W x 20’H x 48’8”L
(4) Box-On-Box Substructure w/ Rotary Beams, V-Door Ramp,
Stairs, (2) Air Receiver Tanks, NATIONAL Deadline Anchor,
Safety Rails, inside Catwalk Trolley, 7’W x 14’L built in Tool
Room (ODS) (3) Stairs, Outside wall Winterized, Jacking door,
12’ X 12’ Setback spreader, internal stairway, Vapor proof lighting,
Skidded with oilfield tail rolls

Pump: (Primary)
HT F-1000 Triplex Mud Pump New 2006,
S/N HT 20060088, 1,000Hp.
w/ LANZOU Pulsation Dampener S/N HT20060070,
MF 5,000 Psi. Pressure Gauge 
FIVE STAR 6”x8”x14” Charging Pump S/N5268 p/b TECO 75 Hp. Electric Motor,
 Chinese 3”Shear Relief Value, Master Skidded w/ (2) Engines belt compound

Pump Power:
CATERPILLAR C-18 Diesel Engine S/N WJHO1283,
575 HP w/24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours # 17,376
CATERPILLAR C-18 Diesel Engine S/N WJH01322,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON18CB500 Air Flex Clutch,
 Mounted Pump Master Skid
Hours#16,277

Pump (Secondary)
HT F-1 000 Triplex Mud Pump New 2006,
S/N HT 20060070, 1,000 Hp.
w/ LANZHOU Pulsation Dampener S/N HT20060069,
MF 5,000 Psi. Pressure Gauge
Five Star 6” x 8” x14” Charging Pump S/N5268 p/b Worldwide 75 Hp.
Electric motor,
3” Shear Relief Valve, Master Skidded w/ (2) Engine belt compound

Pump Power
CATERPILLAR C-18 Diesel Engine S/N WJH-00457,
575 HP w/ 24 volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted pump Master Skid.
Hours#13,788
CATERPILLAR C1-8 Diesel Engine S/N WJH-00373,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours#16,643

Rotating Equipment:

Rotary Table
Chinese ZP 27-1/2”, New 2006, complies with API split master bushings,
W/ drive shaft coupling.

Swivel
Ideco 300

Kelly
5-1/4” x 42’ Hex Kelly W/ HDS Kelly Drive Bushing

Kelly Spinner
OWI 1500 Kelly Spinner S/N 00475B w/ (2) Air Motors, New

Kelly Valves
Upper Kelly Valve.
Lower Kelly Valve

Travelling Equipment
Sentry Rig Equipment Company
260 Ton Capacity New 2006
4G260 Traveling Block w/ (5) 36” Sheaves, 1-1/4” Line,
Unitized “Hydra-Hook” 260 Ton Capacity

Blowout Preventer and Valves
1 Each -13-5/8" X 5000# Jiangsu Xianz hong Petroleum 
Double Gate BOP, Top & Bottom Stud configuration
Including - 1set of 5" Pipe Rams Blocks & 1set of Blind Rams,
With 2 - 4" outlets on each side of Body of BOP

1 Each - 13-5/8" Jiangsu Xianz hong Petroleum  ANNULAR BOP
Includes rubber element

1 Each - 13 5/8" X 5000# Type D Drilling Spool W/ - 2" Side Outlet & 3" Side Outlet
[Matched To Choke Manifold

1 Each - Choke Manifold - 3" X 5000# Complete
 Inc - Steel Flex Line W/ Flanges To Connect
To BOPS or Drilling Spools

Closing Unit
2008 Jiangsu Xianz hong Petroleum Model FXQ640-6
Closing Unit Accumulator, 6 Station,
 Rig Floor Controls and monitor panel,
Complete W/ 15 Bottles, 30 HP Cat 3517 Charge Pump, 21 Air Pumps, & set up
for Nitrogen Bottle Backup
Suitcase Closing Unit Skid 7’-1 0” x 35’ with junk basket

Choke Manifold and Valves
Jiangsu Xianz hong Petroleum Choke Manifold w/ (1) 5-Way Cross,
(3) 4-1/16”x 5M
Gate Valves, (4) 2-9/16” x 5M Gate Valves, (1) Manual
Adjustable Chokes, Hydraulic Adjustable Chokes, Mounted Oil Field Skid.
W/ 2 Kill Valves- & 2-Choke Valves mounted at drilling spool

Rig Houses:
Dog House, DRILLMASTER 9’ 1 1”W x 39’ 1 1”L
Doghouse / Change house Combination w/ 17’5”L
Driller’s House w/ Knowledge Box (5) Lockers, Bench Storage, Heater, Lights.
 5’L Breezeway, 1 7’5”L Change House, w/Bench Storage, (16-Lockers,
Cabinets, Heater & Lights. Oil Field Skidded

Generator/Utility Houses
DRILLMASTER 1 1’10”W x 37’9”L x 11’ 6” T
Utility House w/Lights, Oil Field Skidded to include the following items.

No #1 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01986 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0506, complete with Oil Field skid.
Hours# 17,278

No #2 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01985 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0507, complete with Oil Field skid.
Hours# 16,933

NO. 1 GARDNER-DENVER EBE99N New 2006
Electro Saver II Rotary Screw Air Compressor S/N# S237421,
P/b TOSHIBA 30 Hp. Electric Motor, Mounted 240 Gallon Horizontal Tank.
Hours# 15,128

SIEMENS Interlock Panel, 600 Amp 480 Volt Main Lockout Disconnects breakers.

ALLEN BRADLEY Electrical Load center with magnetic starter & breakers,

SQUARE D 225 amp 240 volt panel with breakers

SQUARE D 75KVA Transformer 480 volt to 240 volt

DRILLMASTER 7’9”W x 13”H x 43’1”L Electrical

Suitcase.

DRILLMASTER 2’5”W x 1 3”H x 36’3”L Electrical Suitcases.

Mud System:
DRILLMASTER 9’6”W x 7’H x 34’5”L, 394 Bbl. Suction Tank
10’L Covered Porch, (3) Compartments,
(3) MAX 2000 Mud Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Oil Field Skidded.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
With internal jetting system, 3 dump gates,

DRILLMASTER 9’6”W x 7’H x 34’7”L, 394 Bbl. Shaker Tank
10’L Covered Porch, (3) Compartments
MAX 2000 Mud Agitator Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Skidded.
With internal jetting system, 3 dump gates,

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5269,
p/b BALDOR 75 Hp. Electric Motor.

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5283,
p/b BALDOR 75 Hp. Electric Motor.

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N2450,

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N3089,

NOI DSN-ZH-10CTX Desander S/N 8714-5732,w/ (2) 10” Cones.

NOI DSL-10GG-4CTX Desilter S/N 8714-5731,w/ (10)4” Cones.

DRILCO “Deep Pit” Degasser p/b TECO 10 Hp. Electric Motor

Bubble Buster: Geothermal Type Bubble Buster

Mud House
DRILLMASTER 9’ 1 1”W x 26’L Mud House w/Mud Hopper, Test Sink,
Ventilation Fan, Electric Heater, Lights, Double Side Door, (2) End Doors, Skidded. 
Includes 7’H Tri-Stand on one end the other end sets on suction tank.

Fuel Tank
DRILLMASTER 7’1 1”Wx8’Hx30’L, 13,860 Gallon Fuel Tank
w/ (2) AMT 1/2 Hp. Fuel Transfer Pumps p/b BALDOR 1/2 Hp. Electric Motors,
with Three (3)Compartment, Combo Lubester Oilfield Skidded.

Water Tank
DRILLMASTER 10’10”W x 8’1”H x 35’L, 529 Bbl. Water Tank
w/ 10’L Covered Extension, Pump Room, OilField Skidded
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N 5420, p/b TECO 20 Hp. Electric Motor.
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N5267, p/b TECO 20 Hp. Electric Motor.

Instrumentation
Weight Indicator
Mud Gauges.

Ancillary Equipment
DRILLMASTER 5’W x 2’4”H x 60’L, 2-Section Catwalk w/ Steel Deck and stands for string blocks.
Pipe Racks 5 Sets 29” x 30’ 1 set 29” x 12’ 1 set 41” x 30’
FIVE STAR “Retriever” Electric Measuring Device S/N 862, w/ 15,000 Ft. of. 092 Wire line
2 sets drill pipe elevators 5”
2 sets of drill pipe slips 5”
2 sets of drill collar slips 7” & 9”
2 sets tongs with all head for pipe & casing
2 sets of safety clamps
Mud box  with 5” rubbers
108” X 4” elevator bails
Crossover, bottom hole, lifting Subs
Air Hoist Air Wrench, Model HUL40, S/N-REM10370, 9000 lb. Pull Rating
Air Hoist Air Wrench, Model KSUL, S/N-REM13962, 10,500 lb. Pull Rating
4,000 Ft. of 1-1/4” Drill Line, Mounted Spooler Stand
3-1/2” X 5,000 Psi. Rotary Hose
Vibrator Hose 2 Each 3 ½” x 18’
Rat hole
Mouse hole
8 rig matting boards
Small hand tools & wrenches
Fluorescent & Mercury-Vapor Rig Lights & Wiring Explosion proof
Atco Office/ living shack all electric w/ oil field skid

Worldrigs ID: WR827
Description :

1979 Jaswell 1200 Drill Rig
Mounted on a Paystar 5000 Truck
Detroit 8V92T Diesel Deck Engine (newer clutch)
Sullair 900 cfm / 350 psi Air Compressor (Recent Compressor and Radiator)
New Chains and updated pumps, gear box
Has cat walk
Recent Oil change
Mounted on a Paystar 5000 Truck
Detroit 671 turbo diesel engine
newer rear tires
5 +4 Transmission
All newer paint

Location : USA

Worldrigs ID: WR796
Model : TXD200 Drill Rig & Package
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm TXD200 Drill Rig
1 Piece Skid Ramp
3 Piece Ramp (3 pieces)
Schramm Unit Trailer
Pipe Handler Trailer
Rig has been stored indoors

Location : Middle East Region

Worldrigs ID: WR544

Model: CME-92 Drill Rig
Manufacturer: CME Drill
Condition: Used

Description :

CME-92 Drill Rig
Deck Engine
Mounted on a 5 Ton Chassis Truck
Ford Gas Engine (Model CSG-649P-6006-E)
511,600 km 
3 Hydraulic Leveling Jacks
No Tooling or Hammer will be provided with the unit

Location : USA

Worldrigs ID: WR83

Model : T64HB
Manufacturer : Schramm
Year : 1972
Condition : used

Description :

1972 Schramm T64HB drill rig
Detroit 8V71 Diesel Deck Engine
425 cfm / 250 psi Air Compressor
Water Injection Pump
Hammer Lubricator
200' ft of Drill Pipe (20' x 4-1/2") and basic tooling included
6" & 8" Hammers & Bits included
Lincoln 225 G7 Welder & Generator on board
Super Rapid Head Travel (loading pipe)
Mounted on a GMC truck
6V53 Diesel Engine
13 Speed Transmission
Flotation Tires (Front), Newer Front Brakes, Newer Transmission

Location : USA

Worldrigs ID: WR178

Model : 1250 Drill Rig
Manufacturer : Failing
Condition : As-Is

Description :

(1) Failing 1250 Drill Rig (being sold for parts)
No Rotary Table
No Mud Pump
No Transfer Case
No Kelly
No Chains
(Basically If You Need A Tower Or Something)
Mounted on a International Truck
Diesel Engine
(1) International 1500 Galloon Water Truck
10 Wheel
Water tank built to bed -O- to haul from pipe beside tank

Location : USA

Worldrigs ID: WR604
Model : T450 Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T-450 Drill Rig
Holte Casing Hammer
Diesel Deck Engine
Air Compressor is low pressure
Mounted on a Truck
Diesel Engine
53,784 Miles on gauge

Could be sold as a package:
Drill Pipe 600’ ft of 4-1/2” & 185’ ft of 3-1/2”
Tulsa Rig Iron Mud shaker
Pipe Truck
assorted bit and reamers

Location : USA

Worldrigs ID: WR202

Model : CTM 10,000 Drill Rig
Manufacturer : DeepRock
Year : 1986
Condition : Used

Description :

Deep Rock CTM 10,000 Drill Rig Package

Package Includes:

Deep Rock CTM 10,000 Commercial Water Well Drilling Rig (Trailer Mounted with Single Axle)
Honda 23 HP engine
Hydraulic Driven
Mission 2 x 1-1/2 Mud Pump
Hydraulic Breakout Wrench
Electric Jib Wrench
Mud Pit
Trailer Mounted

Accessories Include:
2-3/8 x 2-3/8 FMxFM subs
2-3/8 x 3-1/2 FMxFM subs
Drag Bits, 3-1/2 to 6 inch
Tri-Cone Bits, 3-1/2 to 6-1/8 inch
4 inch DTH hammer with 4-1/4 inch Bit
4 inch Shock Absorber sub for D.T.H.
Approximately 200 ft. Drill Rod
Good for drilling shallow Screen Wells & DTH Rock drilling to 150 - 200' ft deep

Included as a Package:

Ingersoll-Rand Gyro-Flo Air Compressor
600 CFM / 100 PSI
Powered by Detroit 671 Diesel Engine
Mounted on a 1974 GMC 6500 Truck
366 Gas Engine (rebuilt with less than 10,000 miles)
Allison 4 speed Transmission
Air Brakes
 
Location : USA

Worldrigs ID: WR540

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR553

Model : CME 75 Drill Rig
Manufacturer : CME Drill
Year : 1987
Condition : Used

Description :

1987 CME 75 Drill Rig
Has 3L6 Moyno Pump
Cat Head
2 Winches
4 Cylinder Gas Engine
The Rig Runs Good
Mounted on a 1988 Ford 750 Tandem Axle (Note: truck is in poor condition).
Also a brand new Auto Hammer in box that can be fitted on the drill

Location : USA

Worldrigs ID: WR661
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 - Range III Drill Rig
120,000 lbs of pullback
Cummins QSK19 Diesel Deck Engine (Very Low Hours)
IR HR2.5 1250 cfm / 350 psi Air Compressor with In/Out box
Rotary Head: 4SV-2-10 Spur gear
Top drive head assembly rated to 8,000 ft. lbs. torque
Single Rod Loader for handling 4.5” o.d. X 30ft long drill rods
Spindle Sub – (4 1/2” x 2 7/8IF")
Water Injection Pump
Hammer Lubricator
Mounted on a CCC (Crane Carrier Carrier) Truck
CAT C13 Diesel Engine

Tooling & Pipe included:
51 (4-1/2 X 30ft X 2-7/8IF") Thread Drill Pipe
12 - (6” X 30ft) Slick Drill Collars
3 - (8” X 30ft) Spiral Drill Collars
Basic Tooling
23 Subs on Steel Platform on Pins

Location : USA

Worldrigs ID: WR693
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 S/S Drill Rig (2)
No Engine currently on deck (but comes with a rebuilt Caterpillar 3406 diesel
engine (heads need torqued down and fuel line needs put back on)
750 CFM / 125 PSI C05 Air Compressor
Bean (FMC) 4-cylinder water injection pump
Dynex main pump & Dynex Head motor
27,500 lb. pullback capability
Gearmatic Hydraulic winch
4-hole Funk Box (hydraulic pump drive)
3 Hydraulic jacks
4 pieces of 25 ft. drill pipe included
Mounted on 1978 CCC (Crane Carrier Company) truck
Powered by Caterpillar 3208 diesel engine,
showing only 4243 miles on odometer
Deck engine and radiator are included but need re-installed
also comes with spare pull down cylinder

Location : USA

Worldrigs ID: WR604
Model : T450 Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T-450 Drill Rig
Holte Casing Hammer
Diesel Deck Engine
Air Compressor is low pressure
Mounted on a Truck
Diesel Engine
53,784 Miles on gauge

Could be sold as a package:
Drill Pipe 600’ ft of 4-1/2” & 185’ ft of 3-1/2”
Tulsa Rig Iron Mud shaker
Pipe Truck
assorted bit and reamers

Location : USA

Worldrigs ID: WR207

SOLD

Model : B-59 Drill Rig
Manufacturer : Mobile
Year : 1995
Condition : Used

Description :

1995 Mobile Drill B-59 drill rig
Cummins 4BT 3.9 Deck Engine (7,468 Hours on gauge)
Clark 3 Speed Transmission
2 Speed Right Angle Box
8,500 LB Main Hoist * 4,000 lbs Auxiliary Hoist * Wireline Hoist *
Safety Drive Hoist * 5,000 lbs CAT head Hoist
In-Out and Sideways Slide Base Rod Clamp * Break Out Wrench
Auxiliary Air Compressor to Run Air Tools
2 Swing Out Auger Racks
Under body Rod Rack
250 Gallon Water Tank – Tool Box Combination
3 – 36” Jacks
Driller Platform
Mounted on a 1995 Ford FT-900 Truck – Tandem Rear Axle
16,000 LB Front Axle, 34,000 LB Rear Axles, 250 HP Cummins Engine, 10 Speed Eaton Road Ranger
Transmission, Air Conditioning, AM- FM Stereo, Dual Fuel Tanks, Tires around 75%
129,600 Miles

Location : USA

Worldrigs ID: WR494

Model : 650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 Drill Rig
CP 450 CFM / 250 PSI Piston Compressor with 750/350(?)
Booster (air clutch needs newdiapragm)
Tiger Tierra Casing Driver
Carousel

Package Includes:
300’ ft of used drill pipe (some need new pins and boxes)
6” and 9” DTH Hammers
6” Tricone button bit

Spare Parts included; main pumps, top head motors, inner cooler, valves for
the compressor, new drive chain for the transfer case

Rig in working order, some oil leaks (packings need replaced).
Mounted on a 1973 International Paystar truck

Location : USA

Worldrigs ID: WR352

Model: 45C Drill Rig
Manufacturer: CME Drill
Year: 2002
Condition: Used

Description :

2002 CME 45C Drill Rig
With 9278 hours
Auto hammer
Wireline winch
Deutz 3 cylinder diesel engine
Mounted on a 2002 Ford F550 Truck 4x4
148,413 miles

Location : USA

Worldrigs ID: WR856
Description :

1992 Ingersoll-Rand T2W Drilling Rig & Package
T2W Drill Outfitted a follows:
IR 900 CFM / 350 PSI Air Compressor
Moyno centrifugal mud pump
500ft of drill pipe on truck (2-7/8” IF), 8-1/2 button bit with stabilizer,
5” hammer, crossover subs included
Mud pan
Mounted on Volvo truck
Cummins N14 diesel engine

Package Includes :
1994 Peterbilt water truck
Grout mixer
2000 gallon in-bed water tank
Auxiliary fuel tank behind cab

Location : USA

Worldrigs ID: WR373

Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
GHH 600 CFM / 250 PSI Air Compressor
CAT D343 Diesel Deck Engine
Mounted on a Kenworth Truck
Diesel Engine

Location : USA